--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/gst_plugins_good/gst/audiofx/audiochebband.c Fri Apr 16 15:15:52 2010 +0300
@@ -0,0 +1,666 @@
+/*
+ * GStreamer
+ * Copyright (C) 2007-2009 Sebastian Dröge <sebastian.droege@collabora.co.uk>
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Library General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Library General Public License for more details.
+ *
+ * You should have received a copy of the GNU Library General Public
+ * License along with this library; if not, write to the
+ * Free Software Foundation, Inc., 59 Temple Place - Suite 330,
+ * Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * Chebyshev type 1 filter design based on
+ * "The Scientist and Engineer's Guide to DSP", Chapter 20.
+ * http://www.dspguide.com/
+ *
+ * For type 2 and Chebyshev filters in general read
+ * http://en.wikipedia.org/wiki/Chebyshev_filter
+ *
+ * Transformation from lowpass to bandpass/bandreject:
+ * http://docs.dewresearch.com/DspHelp/html/IDH_LinearSystems_LowpassToBandPassZ.htm
+ * http://docs.dewresearch.com/DspHelp/html/IDH_LinearSystems_LowpassToBandStopZ.htm
+ *
+ */
+
+/**
+ * SECTION:element-audiochebband
+ *
+ * Attenuates all frequencies outside (bandpass) or inside (bandreject) of a frequency
+ * band. The number of poles and the ripple parameter control the rolloff.
+ *
+ * This element has the advantage over the windowed sinc bandpass and bandreject filter that it is
+ * much faster and produces almost as good results. It's only disadvantages are the highly
+ * non-linear phase and the slower rolloff compared to a windowed sinc filter with a large kernel.
+ *
+ * For type 1 the ripple parameter specifies how much ripple in dB is allowed in the passband, i.e.
+ * some frequencies in the passband will be amplified by that value. A higher ripple value will allow
+ * a faster rolloff.
+ *
+ * For type 2 the ripple parameter specifies the stopband attenuation. In the stopband the gain will
+ * be at most this value. A lower ripple value will allow a faster rolloff.
+ *
+ * As a special case, a Chebyshev type 1 filter with no ripple is a Butterworth filter.
+ *
+ * <note>
+ * Be warned that a too large number of poles can produce noise. The most poles are possible with
+ * a cutoff frequency at a quarter of the sampling rate.
+ * </note>
+ *
+ * <refsect2>
+ * <title>Example launch line</title>
+ * |[
+ * gst-launch audiotestsrc freq=1500 ! audioconvert ! audiochebband mode=band-pass lower-frequency=1000 upper-frequenc=6000 poles=4 ! audioconvert ! alsasink
+ * gst-launch filesrc location="melo1.ogg" ! oggdemux ! vorbisdec ! audioconvert ! audiochebband mode=band-reject lower-frequency=1000 upper-frequency=4000 ripple=0.2 ! audioconvert ! alsasink
+ * gst-launch audiotestsrc wave=white-noise ! audioconvert ! audiochebband mode=band-pass lower-frequency=1000 upper-frequency=4000 type=2 ! audioconvert ! alsasink
+ * ]|
+ * </refsect2>
+ */
+
+#ifdef HAVE_CONFIG_H
+#include "config.h"
+#endif
+
+#include <gst/gst.h>
+#include <gst/base/gstbasetransform.h>
+#include <gst/audio/audio.h>
+#include <gst/audio/gstaudiofilter.h>
+#include <gst/controller/gstcontroller.h>
+
+#include <math.h>
+
+#include "math_compat.h"
+
+#include "audiochebband.h"
+
+#define GST_CAT_DEFAULT gst_audio_cheb_band_debug
+GST_DEBUG_CATEGORY_STATIC (GST_CAT_DEFAULT);
+
+enum
+{
+ PROP_0,
+ PROP_MODE,
+ PROP_TYPE,
+ PROP_LOWER_FREQUENCY,
+ PROP_UPPER_FREQUENCY,
+ PROP_RIPPLE,
+ PROP_POLES
+};
+
+#define DEBUG_INIT(bla) \
+ GST_DEBUG_CATEGORY_INIT (gst_audio_cheb_band_debug, "audiochebband", 0, "audiochebband element");
+
+GST_BOILERPLATE_FULL (GstAudioChebBand, gst_audio_cheb_band,
+ GstAudioFXBaseIIRFilter, GST_TYPE_AUDIO_FX_BASE_IIR_FILTER, DEBUG_INIT);
+
+static void gst_audio_cheb_band_set_property (GObject * object,
+ guint prop_id, const GValue * value, GParamSpec * pspec);
+static void gst_audio_cheb_band_get_property (GObject * object,
+ guint prop_id, GValue * value, GParamSpec * pspec);
+static void gst_audio_cheb_band_finalize (GObject * object);
+
+static gboolean gst_audio_cheb_band_setup (GstAudioFilter * filter,
+ GstRingBufferSpec * format);
+
+enum
+{
+ MODE_BAND_PASS = 0,
+ MODE_BAND_REJECT
+};
+
+#define GST_TYPE_AUDIO_CHEBYSHEV_FREQ_BAND_MODE (gst_audio_cheb_band_mode_get_type ())
+static GType
+gst_audio_cheb_band_mode_get_type (void)
+{
+ static GType gtype = 0;
+
+ if (gtype == 0) {
+ static const GEnumValue values[] = {
+ {MODE_BAND_PASS, "Band pass (default)",
+ "band-pass"},
+ {MODE_BAND_REJECT, "Band reject",
+ "band-reject"},
+ {0, NULL, NULL}
+ };
+
+ gtype = g_enum_register_static ("GstAudioChebBandMode", values);
+ }
+ return gtype;
+}
+
+/* GObject vmethod implementations */
+
+static void
+gst_audio_cheb_band_base_init (gpointer klass)
+{
+ GstElementClass *element_class = GST_ELEMENT_CLASS (klass);
+
+ gst_element_class_set_details_simple (element_class,
+ "Band pass & band reject filter", "Filter/Effect/Audio",
+ "Chebyshev band pass and band reject filter",
+ "Sebastian Dröge <sebastian.droege@collabora.co.uk>");
+}
+
+static void
+gst_audio_cheb_band_class_init (GstAudioChebBandClass * klass)
+{
+ GObjectClass *gobject_class = (GObjectClass *) klass;
+ GstAudioFilterClass *filter_class = (GstAudioFilterClass *) klass;
+
+ gobject_class->set_property = gst_audio_cheb_band_set_property;
+ gobject_class->get_property = gst_audio_cheb_band_get_property;
+ gobject_class->finalize = gst_audio_cheb_band_finalize;
+
+ g_object_class_install_property (gobject_class, PROP_MODE,
+ g_param_spec_enum ("mode", "Mode",
+ "Low pass or high pass mode", GST_TYPE_AUDIO_CHEBYSHEV_FREQ_BAND_MODE,
+ MODE_BAND_PASS,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+ g_object_class_install_property (gobject_class, PROP_TYPE,
+ g_param_spec_int ("type", "Type", "Type of the chebychev filter", 1, 2, 1,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+
+ /* FIXME: Don't use the complete possible range but restrict the upper boundary
+ * so automatically generated UIs can use a slider without */
+ g_object_class_install_property (gobject_class, PROP_LOWER_FREQUENCY,
+ g_param_spec_float ("lower-frequency", "Lower frequency",
+ "Start frequency of the band (Hz)", 0.0, 100000.0,
+ 0.0,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+ g_object_class_install_property (gobject_class, PROP_UPPER_FREQUENCY,
+ g_param_spec_float ("upper-frequency", "Upper frequency",
+ "Stop frequency of the band (Hz)", 0.0, 100000.0, 0.0,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+ g_object_class_install_property (gobject_class, PROP_RIPPLE,
+ g_param_spec_float ("ripple", "Ripple", "Amount of ripple (dB)", 0.0,
+ 200.0, 0.25,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+ /* FIXME: What to do about this upper boundary? With a frequencies near
+ * rate/4 32 poles are completely possible, with frequencies very low
+ * or very high 16 poles already produces only noise */
+ g_object_class_install_property (gobject_class, PROP_POLES,
+ g_param_spec_int ("poles", "Poles",
+ "Number of poles to use, will be rounded up to the next multiply of four",
+ 4, 32, 4,
+ G_PARAM_READWRITE | GST_PARAM_CONTROLLABLE | G_PARAM_STATIC_STRINGS));
+
+ filter_class->setup = GST_DEBUG_FUNCPTR (gst_audio_cheb_band_setup);
+}
+
+static void
+gst_audio_cheb_band_init (GstAudioChebBand * filter,
+ GstAudioChebBandClass * klass)
+{
+ filter->lower_frequency = filter->upper_frequency = 0.0;
+ filter->mode = MODE_BAND_PASS;
+ filter->type = 1;
+ filter->poles = 4;
+ filter->ripple = 0.25;
+
+ filter->lock = g_mutex_new ();
+}
+
+static void
+generate_biquad_coefficients (GstAudioChebBand * filter,
+ gint p, gdouble * a0, gdouble * a1, gdouble * a2, gdouble * a3,
+ gdouble * a4, gdouble * b1, gdouble * b2, gdouble * b3, gdouble * b4)
+{
+ gint np = filter->poles / 2;
+ gdouble ripple = filter->ripple;
+
+ /* pole location in s-plane */
+ gdouble rp, ip;
+
+ /* zero location in s-plane */
+ gdouble iz = 0.0;
+
+ /* transfer function coefficients for the z-plane */
+ gdouble x0, x1, x2, y1, y2;
+ gint type = filter->type;
+
+ /* Calculate pole location for lowpass at frequency 1 */
+ {
+ gdouble angle = (M_PI / 2.0) * (2.0 * p - 1) / np;
+
+ rp = -sin (angle);
+ ip = cos (angle);
+ }
+
+ /* If we allow ripple, move the pole from the unit
+ * circle to an ellipse and keep cutoff at frequency 1 */
+ if (ripple > 0 && type == 1) {
+ gdouble es, vx;
+
+ es = sqrt (pow (10.0, ripple / 10.0) - 1.0);
+
+ vx = (1.0 / np) * asinh (1.0 / es);
+ rp = rp * sinh (vx);
+ ip = ip * cosh (vx);
+ } else if (type == 2) {
+ gdouble es, vx;
+
+ es = sqrt (pow (10.0, ripple / 10.0) - 1.0);
+ vx = (1.0 / np) * asinh (es);
+ rp = rp * sinh (vx);
+ ip = ip * cosh (vx);
+ }
+
+ /* Calculate inverse of the pole location to move from
+ * type I to type II */
+ if (type == 2) {
+ gdouble mag2 = rp * rp + ip * ip;
+
+ rp /= mag2;
+ ip /= mag2;
+ }
+
+ /* Calculate zero location for frequency 1 on the
+ * unit circle for type 2 */
+ if (type == 2) {
+ gdouble angle = M_PI / (np * 2.0) + ((p - 1) * M_PI) / (np);
+ gdouble mag2;
+
+ iz = cos (angle);
+ mag2 = iz * iz;
+ iz /= mag2;
+ }
+
+ /* Convert from s-domain to z-domain by
+ * using the bilinear Z-transform, i.e.
+ * substitute s by (2/t)*((z-1)/(z+1))
+ * with t = 2 * tan(0.5).
+ */
+ if (type == 1) {
+ gdouble t, m, d;
+
+ t = 2.0 * tan (0.5);
+ m = rp * rp + ip * ip;
+ d = 4.0 - 4.0 * rp * t + m * t * t;
+
+ x0 = (t * t) / d;
+ x1 = 2.0 * x0;
+ x2 = x0;
+ y1 = (8.0 - 2.0 * m * t * t) / d;
+ y2 = (-4.0 - 4.0 * rp * t - m * t * t) / d;
+ } else {
+ gdouble t, m, d;
+
+ t = 2.0 * tan (0.5);
+ m = rp * rp + ip * ip;
+ d = 4.0 - 4.0 * rp * t + m * t * t;
+
+ x0 = (t * t * iz * iz + 4.0) / d;
+ x1 = (-8.0 + 2.0 * iz * iz * t * t) / d;
+ x2 = x0;
+ y1 = (8.0 - 2.0 * m * t * t) / d;
+ y2 = (-4.0 - 4.0 * rp * t - m * t * t) / d;
+ }
+
+ /* Convert from lowpass at frequency 1 to either bandpass
+ * or band reject.
+ *
+ * For bandpass substitute z^(-1) with:
+ *
+ * -2 -1
+ * -z + alpha * z - beta
+ * ----------------------------
+ * -2 -1
+ * beta * z - alpha * z + 1
+ *
+ * alpha = (2*a*b)/(1+b)
+ * beta = (b-1)/(b+1)
+ * a = cos((w1 + w0)/2) / cos((w1 - w0)/2)
+ * b = tan(1/2) * cot((w1 - w0)/2)
+ *
+ * For bandreject substitute z^(-1) with:
+ *
+ * -2 -1
+ * z - alpha * z + beta
+ * ----------------------------
+ * -2 -1
+ * beta * z - alpha * z + 1
+ *
+ * alpha = (2*a)/(1+b)
+ * beta = (1-b)/(1+b)
+ * a = cos((w1 + w0)/2) / cos((w1 - w0)/2)
+ * b = tan(1/2) * tan((w1 - w0)/2)
+ *
+ */
+ {
+ gdouble a, b, d;
+ gdouble alpha, beta;
+ gdouble w0 =
+ 2.0 * M_PI * (filter->lower_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+ gdouble w1 =
+ 2.0 * M_PI * (filter->upper_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+
+ if (filter->mode == MODE_BAND_PASS) {
+ a = cos ((w1 + w0) / 2.0) / cos ((w1 - w0) / 2.0);
+ b = tan (1.0 / 2.0) / tan ((w1 - w0) / 2.0);
+
+ alpha = (2.0 * a * b) / (1.0 + b);
+ beta = (b - 1.0) / (b + 1.0);
+
+ d = 1.0 + beta * (y1 - beta * y2);
+
+ *a0 = (x0 + beta * (-x1 + beta * x2)) / d;
+ *a1 = (alpha * (-2.0 * x0 + x1 + beta * x1 - 2.0 * beta * x2)) / d;
+ *a2 =
+ (-x1 - beta * beta * x1 + 2.0 * beta * (x0 + x2) +
+ alpha * alpha * (x0 - x1 + x2)) / d;
+ *a3 = (alpha * (x1 + beta * (-2.0 * x0 + x1) - 2.0 * x2)) / d;
+ *a4 = (beta * (beta * x0 - x1) + x2) / d;
+ *b1 = (alpha * (2.0 + y1 + beta * y1 - 2.0 * beta * y2)) / d;
+ *b2 =
+ (-y1 - beta * beta * y1 - alpha * alpha * (1.0 + y1 - y2) +
+ 2.0 * beta * (-1.0 + y2)) / d;
+ *b3 = (alpha * (y1 + beta * (2.0 + y1) - 2.0 * y2)) / d;
+ *b4 = (-beta * beta - beta * y1 + y2) / d;
+ } else {
+ a = cos ((w1 + w0) / 2.0) / cos ((w1 - w0) / 2.0);
+ b = tan (1.0 / 2.0) * tan ((w1 - w0) / 2.0);
+
+ alpha = (2.0 * a) / (1.0 + b);
+ beta = (1.0 - b) / (1.0 + b);
+
+ d = -1.0 + beta * (beta * y2 + y1);
+
+ *a0 = (-x0 - beta * x1 - beta * beta * x2) / d;
+ *a1 = (alpha * (2.0 * x0 + x1 + beta * x1 + 2.0 * beta * x2)) / d;
+ *a2 =
+ (-x1 - beta * beta * x1 - 2.0 * beta * (x0 + x2) -
+ alpha * alpha * (x0 + x1 + x2)) / d;
+ *a3 = (alpha * (x1 + beta * (2.0 * x0 + x1) + 2.0 * x2)) / d;
+ *a4 = (-beta * beta * x0 - beta * x1 - x2) / d;
+ *b1 = (alpha * (-2.0 + y1 + beta * y1 + 2.0 * beta * y2)) / d;
+ *b2 =
+ -(y1 + beta * beta * y1 + 2.0 * beta * (-1.0 + y2) +
+ alpha * alpha * (-1.0 + y1 + y2)) / d;
+ *b3 = (alpha * (beta * (-2.0 + y1) + y1 + 2.0 * y2)) / d;
+ *b4 = -(-beta * beta + beta * y1 + y2) / d;
+ }
+ }
+}
+
+static void
+generate_coefficients (GstAudioChebBand * filter)
+{
+ if (GST_AUDIO_FILTER (filter)->format.rate == 0) {
+ gdouble *a = g_new0 (gdouble, 1);
+
+ a[0] = 1.0;
+ gst_audio_fx_base_iir_filter_set_coefficients (GST_AUDIO_FX_BASE_IIR_FILTER
+ (filter), a, 1, NULL, 0);
+ GST_LOG_OBJECT (filter, "rate was not set yet");
+ return;
+ }
+
+ if (filter->upper_frequency <= filter->lower_frequency) {
+ gdouble *a = g_new0 (gdouble, 1);
+
+ a[0] = (filter->mode == MODE_BAND_PASS) ? 0.0 : 1.0;
+ gst_audio_fx_base_iir_filter_set_coefficients (GST_AUDIO_FX_BASE_IIR_FILTER
+ (filter), a, 1, NULL, 0);
+
+ GST_LOG_OBJECT (filter, "frequency band had no or negative dimension");
+ return;
+ }
+
+ if (filter->upper_frequency > GST_AUDIO_FILTER (filter)->format.rate / 2) {
+ filter->upper_frequency = GST_AUDIO_FILTER (filter)->format.rate / 2;
+ GST_LOG_OBJECT (filter, "clipped upper frequency to nyquist frequency");
+ }
+
+ if (filter->lower_frequency < 0.0) {
+ filter->lower_frequency = 0.0;
+ GST_LOG_OBJECT (filter, "clipped lower frequency to 0.0");
+ }
+
+ /* Calculate coefficients for the chebyshev filter */
+ {
+ gint np = filter->poles;
+ gdouble *a, *b;
+ gint i, p;
+
+ a = g_new0 (gdouble, np + 5);
+ b = g_new0 (gdouble, np + 5);
+
+ /* Calculate transfer function coefficients */
+ a[4] = 1.0;
+ b[4] = 1.0;
+
+ for (p = 1; p <= np / 4; p++) {
+ gdouble a0, a1, a2, a3, a4, b1, b2, b3, b4;
+ gdouble *ta = g_new0 (gdouble, np + 5);
+ gdouble *tb = g_new0 (gdouble, np + 5);
+
+ generate_biquad_coefficients (filter, p, &a0, &a1, &a2, &a3, &a4, &b1,
+ &b2, &b3, &b4);
+
+ memcpy (ta, a, sizeof (gdouble) * (np + 5));
+ memcpy (tb, b, sizeof (gdouble) * (np + 5));
+
+ /* add the new coefficients for the new two poles
+ * to the cascade by multiplication of the transfer
+ * functions */
+ for (i = 4; i < np + 5; i++) {
+ a[i] =
+ a0 * ta[i] + a1 * ta[i - 1] + a2 * ta[i - 2] + a3 * ta[i - 3] +
+ a4 * ta[i - 4];
+ b[i] =
+ tb[i] - b1 * tb[i - 1] - b2 * tb[i - 2] - b3 * tb[i - 3] -
+ b4 * tb[i - 4];
+ }
+ g_free (ta);
+ g_free (tb);
+ }
+
+ /* Move coefficients to the beginning of the array
+ * and multiply the b coefficients with -1 to move from
+ * the transfer function's coefficients to the difference
+ * equation's coefficients */
+ b[4] = 0.0;
+ for (i = 0; i <= np; i++) {
+ a[i] = a[i + 4];
+ b[i] = -b[i + 4];
+ }
+
+ /* Normalize to unity gain at frequency 0 and frequency
+ * 0.5 for bandreject and unity gain at band center frequency
+ * for bandpass */
+ if (filter->mode == MODE_BAND_REJECT) {
+ /* gain is sqrt(H(0)*H(0.5)) */
+
+ gdouble gain1 =
+ gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1, b, np + 1,
+ 1.0, 0.0);
+ gdouble gain2 =
+ gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1, b, np + 1,
+ -1.0, 0.0);
+
+ gain1 = sqrt (gain1 * gain2);
+
+ for (i = 0; i <= np; i++) {
+ a[i] /= gain1;
+ }
+ } else {
+ /* gain is H(wc), wc = center frequency */
+
+ gdouble w1 =
+ 2.0 * M_PI * (filter->lower_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+ gdouble w2 =
+ 2.0 * M_PI * (filter->upper_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+ gdouble w0 = (w2 + w1) / 2.0;
+ gdouble zr = cos (w0), zi = sin (w0);
+ gdouble gain =
+ gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1, b, np + 1, zr,
+ zi);
+
+ for (i = 0; i <= np; i++) {
+ a[i] /= gain;
+ }
+ }
+
+ gst_audio_fx_base_iir_filter_set_coefficients (GST_AUDIO_FX_BASE_IIR_FILTER
+ (filter), a, np + 1, b, np + 1);
+
+ GST_LOG_OBJECT (filter,
+ "Generated IIR coefficients for the Chebyshev filter");
+ GST_LOG_OBJECT (filter,
+ "mode: %s, type: %d, poles: %d, lower-frequency: %.2f Hz, upper-frequency: %.2f Hz, ripple: %.2f dB",
+ (filter->mode == MODE_BAND_PASS) ? "band-pass" : "band-reject",
+ filter->type, filter->poles, filter->lower_frequency,
+ filter->upper_frequency, filter->ripple);
+
+ GST_LOG_OBJECT (filter, "%.2f dB gain @ 0Hz",
+ 20.0 * log10 (gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1, b,
+ np + 1, 1.0, 0.0)));
+ {
+ gdouble w1 =
+ 2.0 * M_PI * (filter->lower_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+ gdouble w2 =
+ 2.0 * M_PI * (filter->upper_frequency /
+ GST_AUDIO_FILTER (filter)->format.rate);
+ gdouble w0 = (w2 + w1) / 2.0;
+ gdouble zr, zi;
+
+ zr = cos (w1);
+ zi = sin (w1);
+ GST_LOG_OBJECT (filter, "%.2f dB gain @ %dHz",
+ 20.0 * log10 (gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1,
+ b, np + 1, zr, zi)), (int) filter->lower_frequency);
+ zr = cos (w0);
+ zi = sin (w0);
+ GST_LOG_OBJECT (filter, "%.2f dB gain @ %dHz",
+ 20.0 * log10 (gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1,
+ b, np + 1, zr, zi)),
+ (int) ((filter->lower_frequency + filter->upper_frequency) / 2.0));
+ zr = cos (w2);
+ zi = sin (w2);
+ GST_LOG_OBJECT (filter, "%.2f dB gain @ %dHz",
+ 20.0 * log10 (gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1,
+ b, np + 1, zr, zi)), (int) filter->upper_frequency);
+ }
+ GST_LOG_OBJECT (filter, "%.2f dB gain @ %dHz",
+ 20.0 * log10 (gst_audio_fx_base_iir_filter_calculate_gain (a, np + 1, b,
+ np + 1, -1.0, 0.0)),
+ GST_AUDIO_FILTER (filter)->format.rate / 2);
+ }
+}
+
+static void
+gst_audio_cheb_band_finalize (GObject * object)
+{
+ GstAudioChebBand *filter = GST_AUDIO_CHEB_BAND (object);
+
+ g_mutex_free (filter->lock);
+ filter->lock = NULL;
+
+ G_OBJECT_CLASS (parent_class)->finalize (object);
+}
+
+static void
+gst_audio_cheb_band_set_property (GObject * object, guint prop_id,
+ const GValue * value, GParamSpec * pspec)
+{
+ GstAudioChebBand *filter = GST_AUDIO_CHEB_BAND (object);
+
+ switch (prop_id) {
+ case PROP_MODE:
+ g_mutex_lock (filter->lock);
+ filter->mode = g_value_get_enum (value);
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ case PROP_TYPE:
+ g_mutex_lock (filter->lock);
+ filter->type = g_value_get_int (value);
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ case PROP_LOWER_FREQUENCY:
+ g_mutex_lock (filter->lock);
+ filter->lower_frequency = g_value_get_float (value);
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ case PROP_UPPER_FREQUENCY:
+ g_mutex_lock (filter->lock);
+ filter->upper_frequency = g_value_get_float (value);
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ case PROP_RIPPLE:
+ g_mutex_lock (filter->lock);
+ filter->ripple = g_value_get_float (value);
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ case PROP_POLES:
+ g_mutex_lock (filter->lock);
+ filter->poles = GST_ROUND_UP_4 (g_value_get_int (value));
+ generate_coefficients (filter);
+ g_mutex_unlock (filter->lock);
+ break;
+ default:
+ G_OBJECT_WARN_INVALID_PROPERTY_ID (object, prop_id, pspec);
+ break;
+ }
+}
+
+static void
+gst_audio_cheb_band_get_property (GObject * object, guint prop_id,
+ GValue * value, GParamSpec * pspec)
+{
+ GstAudioChebBand *filter = GST_AUDIO_CHEB_BAND (object);
+
+ switch (prop_id) {
+ case PROP_MODE:
+ g_value_set_enum (value, filter->mode);
+ break;
+ case PROP_TYPE:
+ g_value_set_int (value, filter->type);
+ break;
+ case PROP_LOWER_FREQUENCY:
+ g_value_set_float (value, filter->lower_frequency);
+ break;
+ case PROP_UPPER_FREQUENCY:
+ g_value_set_float (value, filter->upper_frequency);
+ break;
+ case PROP_RIPPLE:
+ g_value_set_float (value, filter->ripple);
+ break;
+ case PROP_POLES:
+ g_value_set_int (value, filter->poles);
+ break;
+ default:
+ G_OBJECT_WARN_INVALID_PROPERTY_ID (object, prop_id, pspec);
+ break;
+ }
+}
+
+/* GstAudioFilter vmethod implementations */
+
+static gboolean
+gst_audio_cheb_band_setup (GstAudioFilter * base, GstRingBufferSpec * format)
+{
+ GstAudioChebBand *filter = GST_AUDIO_CHEB_BAND (base);
+
+ generate_coefficients (filter);
+
+ return GST_AUDIO_FILTER_CLASS (parent_class)->setup (base, format);
+}