/** @file ../include/net/if_var.h

@internalComponent

*/

/** @struct ifnet

Structure defining a network interface.

ifnet and its related packet queues are protected by if_serializer.

Callers of if_output, if_ioctl, if_start, if_watchdog, if_init, if_resolvemulti, and if_poll hold if_serializer.  

Device drivers usually use the same serializer for their interrupt but this is not required.

However, the device driver must be holding if_serializer when it calls if_input.  

Note that the serializer may be temporarily released within if_input to avoid a deadlock (e.g. when fast-forwarding or bridging packets between interfaces).

If a device driver installs the same serializer for its interrupt as for ifnet, then the driver only really needs to worry about further serialization in timeout based entry points.  

All other entry points will already be serialized.  Older ISA drivers still using the old interrupt infrastructure will have to obtain and release the serializer in their interrupt routine themselves.

@publishedAll

@externallyDefinedApi

*/

/** @struct ifaddr 

The ifaddr structure contains information about one address of an interface.  

They are maintained by the different address families, are allocated and attached when an address is set, and are linked together so all addresses for an interface can be located.

@publishedAll

@externallyDefinedApi

*/

/** @var ifaddr::ifa_addr

address of interface

*/

/** @var ifaddr::ifa_dstaddr

other end of p-to-p link

*/

/** @var ifaddr::ifa_netmask

used to determine subnet

*/

/** @var ifaddr::if_data

not all members are meaningful 

*/

/** @var ifaddr::ifa_ifp

back-pointer to interface

*/

/** @var ifaddr::ifa_link

queue macro glue

*/

/** @var ifaddr::ifa_rtrequest

check or clean routes 

*/

/** @var ifaddr::ifa_flags

mostly rt_flags for cloning

*/

/** @var ifaddr::ifa_refcnt

references to this structure 

*/

/** @var ifaddr::ifa_metric

cost of going out this interface

*/

/** @var ifaddr::ifa_rt

XXXX for ROUTETOIF 

*/

/** @var ifaddr::ifa_claim_addr

check if an addr goes to this if

*/

/** @struct ifqueue

Structure defining a queue for a network interface.

@publishedAll

@released

*/

/** @struct ifmultiaddr

Multicast address structure.  This is analogous to the ifaddr structure except that it keeps track of multicast addresses.

Also, the reference count here is a count of requests for this address, not a count of pointers to this structure.

@publishedAll

@released

*/

/** @var ifmultiaddr::ifma_link

queue macro glue

*/

/** @var ifmultiaddr::ifma_addr

address this membership is for

*/

/** @var ifmultiaddr::ifma_lladdr

link-layer translation, if any

*/

/** @var ifmultiaddr::ifma_ifp

back-pointer to interface

*/

/** @var ifmultiaddr::ifma_refcount

reference count 

*/

/** @var ifmultiaddr::ifma_protospec

protocol-specific state, if any

*/

/** @def IF_QFULL(ifq)	

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_DROP(ifq)

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_QLEN(ifq) 

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_QEMPTY(ifq)

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_ENQUEUE(ifq, m)

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_PREPEND(ifq, m)

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_DEQUEUE(ifq, m)

Output queues and slow device input queues are queues of messages stored on ifqueue structures (defined above).  

Entries are added to and deleted from these structures by these macros, which should be called with ipl raised to splimp().

@publishedAll

@released

*/

/** @def IF_POLL(ifq, m) 

polling related function.

@publishedAll

@released

*/

/** @def IF_DRAIN(ifq)

To drain a queue

@publishedAll

@released

*/