<?xml version="1.0" encoding="utf-8"?>

<!-- Copyright (c) 2007-2010 Nokia Corporation and/or its subsidiary(-ies) All rights reserved. -->

<!-- This component and the accompanying materials are made available under the terms of the License 

"Eclipse Public License v1.0" which accompanies this distribution, 

and is available at the URL "http://www.eclipse.org/legal/epl-v10.html". -->

<!-- Initial Contributors:

    Nokia Corporation - initial contribution.

Contributors: 

-->

<!DOCTYPE concept

  PUBLIC "-//OASIS//DTD DITA Concept//EN" "concept.dtd">

<concept id="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC" xml:lang="en"><title>Inactivity

Monitoring and Peripheral Low Power States</title><shortdesc>Peripheral inactivity can be defined as the state when that peripheral’s

driver has no pending request and is not performing background tasks.</shortdesc><prolog><metadata><keywords/></metadata></prolog><conbody>

<p>It is recommended that peripheral drivers monitor peripheral inactivity

because they are in the best position to understand the current hardware requirement. </p>

<p>The preferred approach is to implement inactivity monitoring in the platform

specific portion of peripheral drivers. However it is not always possible

to safely do it that way. In this case, an interface between the platform

specific and generic portions of the driver might need to be devised leading

to, in the future, inactivity monitoring functionality or assistance being

included in generic components. </p>

<p>In some cases the developer of the driver might decide to implement inactivity

monitoring with a grace delay, using timers. For example, consider a peripheral

used as a data input device. If the only way that the platform specific layer

of the peripheral driver has any knowledge that an input request is pending,

and that data is arriving, is when an incoming unit of data causes an interrupt,

then the resulting ISR (or deferred DFC) could re-start a timer with a suitable

period. Inactivity could be monitored in the timer callback. This guarantees

that if another unit of data arrives before the timer expiration, the peripheral

is still in its operational power state. </p>

<ul>

<li id="GUID-D72B1509-0CFD-55D2-B4D3-84A6130AC3C8"><p> <xref href="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC.dita#GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC/GUID-1817A738-2351-526F-881D-7EB479E93C4C">Peripheral Power States</xref> </p> </li>

<li id="GUID-C6CAE535-2406-53FF-85C6-18552831DB94"><p> <xref href="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC.dita#GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC/GUID-1E31C6B9-6F69-50C5-908A-BCC648D4D8B1">Peripheral standby</xref> </p> </li>

<li id="GUID-36E6FC1E-C3E8-5A78-AF77-D54486719BFF"><p> <xref href="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC.dita#GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC/GUID-DCB8EA90-9B5F-5BA1-8D22-124980AC6B34">Moving peripherals to a low power state</xref> </p> </li>

<li id="GUID-927DF4E2-18A3-51B5-9A46-02C63013954C"><p> <xref href="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC.dita#GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC/GUID-81231D49-0F35-582D-BDB3-DC1A08C2E448">High latency low power states and non-transparent transitions</xref> </p> </li>

<li id="GUID-9DC49460-BE85-5979-B52D-DB6AC7E218D5"><p> <xref href="GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC.dita#GUID-1D3E61BD-C09D-51FD-A10B-22392FDAEFEC/GUID-CA1BB80F-5A1C-5B66-8091-84625A0A9CFB">Peripheral power state diagram and transitions</xref> </p> </li>

</ul>

<section id="GUID-1817A738-2351-526F-881D-7EB479E93C4C"><title>Peripheral

Power States</title> <p>It is possible that a particular ASSP allows peripheral

hardware blocks to be independently transitioned to a low power state. From

the point of view of power consumption, the base port might consider that

those peripherals have three logical power states: </p> <ul>

<li id="GUID-49BC931A-15BE-5AC3-8F8F-1C3EFBFC0806"><p> <i>Operational Power</i> –

the peripheral is either processing some request, or performing a background

task with data transactions to or from it, or the peripheral is being kept

in this state in anticipation that data will be input to it, and is drawing

an amount of power corresponding to one of its possible modes of operation. </p> </li>

<li id="GUID-93AA050E-44F7-5B73-A8A2-4F70A2067E42"><p> <i>Low Power</i> –

the peripheral is “idling” after a period of inactivity has been detected,

drawing a minimal amount of power required to preserve its internal state.

The peripheral should be able to keep its internal state and transition from

this to the Operational Power state with a negligible delay and with no impact

on the performance of either the peripheral driver or the upper layer components

that use it. </p> </li>

<li id="GUID-8A39F42D-B928-5DE2-B79A-A1EABBF696E4"><p> <i>Off</i> – the peripheral

power has been cut off, and only leakage accounts for power consumption. No

state is preserved and the delay to a return to full power is not negligible. </p> </li>

</ul> <p>Note that peripheral power states are a notion that only applies

to the peripheral hardware block, and not to the driver. The peripheral driver

is the component that requests the peripheral to transition between these

states. </p> <p>Note also that both Operational and Low Power states are subsets

of the Peripheral "Active" state. In some cases the differences in power consumption

between the Operational and Low Power modes might not be significant as, with

some hardware, only part of the peripheral needs to be operational to service

a particular type of request. </p> </section>

<section id="GUID-1E31C6B9-6F69-50C5-908A-BCC648D4D8B1"><title>Peripheral

standby</title> <p>Some ASSPs make provision for a peripheral standby mode,

where individual peripherals can be transitioned to a low power consumption

mode of operation under software control, usually by writing to an ASIC internal

register. </p> <p>If the peripheral is capable of keeping its internal state,

and the transition out of this mode is either done automatically on hardware,

or controlled by software, but has no impact on the performance of the peripheral

driver or on the users of this peripheral, and can be done with negligible

delay, then the peripheral standby mode could be considered a low power state

as above. </p> </section>

<section id="GUID-DCB8EA90-9B5F-5BA1-8D22-124980AC6B34"><title>Moving peripherals

to a low power state</title> <p>It is assumed that peripherals can be transitioned

between power states under the peripheral driver's software control. However,

transitioning peripherals to a low power state should only be performed if

it can be done transparently to the users and consumers of the services provided

by that peripheral. Negligible interactive delays may be acceptable, data

loss is not acceptable. </p> <p>The transition of a peripheral to a low power

state can be requested by the platform-dependent layers of that peripheral

driver after inactivity, as defined above, has been detected. That request

usually assumes the form of a request to turn a controllable power resource

off. The request should be handled by the ASSP/Variant component that manages

platform power resources (the resource manager). </p> <p>It can also assume

the form of an operation required to put the peripheral in standby mode. In

this case the peripheral driver is totally responsible for handling the transition

to the low power state. </p> </section>

<section id="GUID-81231D49-0F35-582D-BDB3-DC1A08C2E448"><title>High latency

low power states and non-transparent transitions</title> <p>This guide is

only concerned with peripheral low power states that can be reached and left

with no impact on system performance. However, it is possible that transitions

to and from a peripheral low power state are long enough to have an impact

on system performance, or cause loss of data, or the peripheral is not capable

of detecting the hardware events required to guarantee correct operation while

in a low power state. If this is the case, then the decision to transition

to a low power state cannot be taken solely by the peripheral driver, and

will have to be taken in agreement with the users and consumers of the services

provided by this peripheral. </p> </section>

<section id="GUID-CA1BB80F-5A1C-5B66-8091-84625A0A9CFB"><title>Peripheral

power state diagram and transitions</title> <fig id="GUID-A1F2E1D2-FA3B-55C3-B7A3-1AECBDC37453">

<title>Peripheral power state diagram</title>

<image href="GUID-E55B594F-CC84-5984-9307-9819F6EBEB7F_d0e389916_href.png" placement="inline"/>

</fig> <p>It can be assumed that when the peripheral driver is loaded, the

peripheral is put into the <i>Low Power</i> state. If a new request is asserted

on that peripheral driver from a user of that peripheral (which can include

another dependent peripheral driver or user side Engine/server/application),

the peripheral should move to its <i>Operational Power</i> state. The driver

can then start monitoring for peripheral inactivity, and when that is detected,

and no other dependent peripheral is using this peripheral, it can move the

peripheral back to the <i>Low Power</i> state. </p> <p>If, however, the power

manager requests the driver to power down the peripheral and no other dependent

peripheral is using it, it then moves into its <i>Off</i> state from which

it can only return to the <i>Operational Power</i> state when the power manager

issues a power up request. Moving from the <i>Off</i> state to the <i>Operational

Power</i> state is a relatively lengthy operation and requires resetting the

internal state of the peripheral. </p> <p>If another dependent peripheral

is using this peripheral, and the power manager issues a power down request,

then the driver keeps the peripheral in its operational power state until

the dependent peripheral relinquishes its request on it. </p> <p>From the <i>Low

Power</i> state, a peripheral can also be turned Off (unconditionally) if

the power manager so requests. It can be moved back to the <i>Operational

Power</i> state on an internal event (Interrupt, Timer). </p> <fig id="GUID-C5AED7DE-18A1-5FBF-B1E4-44067F246CC2">

<title>Peripheral power states</title>

<image href="GUID-EFEACBE5-B9E1-5315-88CA-DA3B7C1BFCE0_d0e389963_href.png" placement="inline"/>

</fig> </section>

</conbody></concept>