Channel -Implementation

diff -r ebc84c812384 -r 46218c8b8afa Symbian3/PDK/Source/GUID-AF71FDC2-A8CC-5035-91FE-36212844BC07.dita --- a/Symbian3/PDK/Source/GUID-AF71FDC2-A8CC-5035-91FE-36212844BC07.dita Thu Mar 11 15:24:26 2010 +0000 +++ b/Symbian3/PDK/Source/GUID-AF71FDC2-A8CC-5035-91FE-36212844BC07.dita Thu Mar 11 18:02:22 2010 +0000 @@ -1,210 +1,210 @@ - - - - - -Channel -ImplementationDescribes how to use the template port to implement the physical -channel for the Digitizer Driver. -

Define the -size of the digitizer

The following four constants defined at the -top of the template implementation in xyin.cpp define -the origin and size of the digitizer device in pixels. Modify the values to -define your own origin and size.

const TUint KConfigXyOffsetX = 0; -const TUint KConfigXyOffsetY = 0; -const TUint KConfigXyWidth = 640; // pixels per line -const TUint KConfigXyHeight = 480; // lines per panel -

This is information that is returned when calls are made:

user side to HAL::Get() passing -the attribute(s) EPenX and EPenY
kernel side to Kern::HalFunction(), -passing group EHalGroupdigitizer and function-id EdigitizerHalXYInfo

See User-Side -Hardware Abstraction.

The following four constants define the -digitizer origin and size in digitizer ADC coordinates. Modify the values -for your own digitizer:

const Tint KConfigXySpreadX = 4096; // maximum valid X spread -const Tint KConfigXySpreadY = 4096; // maximum valid Y spread -const Tint KConfigXyMinX = 0; // minimum valid X value -const Tint KConfigXyMinY = 0; // minimum valid Y value -

Implement power -on behaviour

In the template port, this is implemented by DTemplatedigitizer::digitizerPowerUp(). -Note that this function is not derived from any base class function.

Add code to this function -to do these things:
1. Clear all digitizer -interrupts.
2. Request power resources -from the power controller. This will power the device up from sleep mode. -Note that power up, and power down, can be implemented later.
3. Configure the hardware -so that it generates an interrupt when the digitizer is touched.
Make sure that the digitizer -interrupt is defined. In the template port, the interrupt id is defined as -the constant:
const TInt KIntIddigitizer=EAsspIntIdC
in -the file ...\template\template_assp\template_assp.h.
Make sure that the interrupt -controller is configured for the digitizer interrupt. See Interrupt -Dispatcher.

Implement Ddigitizer::WaitForPenDown()

This -code is executed at startup or whenever the pen is lifted up. It implements -a request for an interrupt to be generated when the pen next touches the digitizer. -It is called by the platform independent layer:

at startup
when the pen is removed -from the digitizer after a pen-up event has been issued.

There are two main cases to deal with: the digitizer is powering -down; the digitizer is not powering down

The digitizer is powering -down

The implementation for this case can be left until later. -It is discussed in Implement -power up and power down handling.

The digitizer is not powering -down

To deal with this case, your implementation needs to:

clear the digitizer -interrupt
set up the hardware -so that it can detect when the digitizer is touched.

The pen interrupt is now enabled; if the digitizer is now touched, -the pen interrupt ISR (interrupt service routine) DTemplatedigitizer::PenInterrupt() is -called.

In the template port, the ISR includes the statement:

__KTRACE_OPT(KHARDWARE,Kern::Printf("I"));

and -means that if the KHARDWARE tracing flag has been set, and -tracing is on, then a single “I” is printed whenever the digitizer is touched.

Tracing -note

If the KEXTENSION, KPOWER and KHARDWARE tracing -flags have been set, and tracing is on, then by the time WaitForPenDown() is -called, you should be able to see the following sequence of calls in the trace:

DoCreate()
digitizerPowerUp()
WaitForPenDown()

Implement the -pen interrupt ISR

In the template port, the interrupt service routine -(ISR) that handles a pen interrupt is implemented by DTemplatedigitizer::PenInterrupt(). -Note that this function is not derived from any base class function.

There -are two main things to consider here:

You need to add code -to the start of the function to decide whether the pen is now up (i.e. removed -from the screen panel), or whether the pen is now down (i.e. touching the -digitizer panel). To make the decision, you may need to read the appropriate -hardware register. The detail depends on the hardware.
If the pen is down, -you need to check the value of the configurable constant KPenDownDelayTime. What you do next depends on the value of this constant:
- If the value is greater -than zero, then you do not need to change the code at this time. The existing -code just starts a timer to delay the beginning of the collection of samples. -Note, however, that you will need to modify the debounce timer callback function timerIntExpired() to -clear the digitizer interrupt - see Add -code to the debounce timer callback function.
- If the value is zero, -then you must clear the digitizer interrupt here in this function, PenInterrupt().

Initialise -sampling

In the template port, the initialisation of sampling is -implemented in the first half of the function DTemplatedigitizer::TakeSample() function. -Note that this function is not derived from any base class function.

There -are two main things to consider here:

You need to decide whether -the pen is up or down. Set the variable penDown to ETrue if -the pen is down or EFalse if the pen is up.

To -do this you may need to read the appropriate hardware register - the detail -depends on the hardware.
Change the section of -code that is executed when the pen is found to be up after a power on, i.e. -the block of code:
if (iState==E_HW_PowerUp) - { - if (!penDown) - { - ... - }
The block of code needs to do the following:
- reset the sample buffer
- clear the digitizer -interrupt
- set up the hardware -so that it can detect when the digitizer is touched
- enable the digitizer -interrupt.

Take sample -readings

In the template port, the initialisation of sampling is -implemented in the second half of the function DTemplatedigitizer::TakeSample() function. -Note that this function is not derived from any base class function.

This -code is executed while the pen is down, and needs to do the following:

read the hardware for -the digitizer samples and put the results into the sample buffer. The sample -buffer resides in the platform independent layer.
set up the hardware -so that it can detect when the digitizer is touched
schedule the reading -of the next sample using a one shot timer; the time interval is defined by -the value of the configurable constant KInterSampleTime
when a complete group -of samples has been taken, tell the platform independent layer by calling RawSampleValid(); -the function is a member of the base class Ddigitizer.

Tracing note

If the KHARDWARE tracing flag -has been set, and tracing is on, then it should be possible to move the pen -over the screen and see the raw sample values on the debug output. Check they -are correct.

Add code to -the debounce timer callback function

In the template port, the -debounce timer callback function is implemented by the local function timerIntExpired().

If -not already done in Implement -the pen interrupt ISR, add code to this callback function to clear -the digitizer interrupt.

Deal with a -pen up interrupt

If the digitizer generates an interrupt when the -pen is lifted, then you need to add code to the pen interrupt ISR to handle -this. This is the same function, DTemplatedigitizer::PenInterrupt(), -referred to in Implement -the pen interrupt ISR.

The code should:

clear the digitizer -interrupt.
set up the hardware -so that it can detect when the digitizer panel is touched.

If there is no pen up interrupt by design, then you need to add code -into the DTemplatedigitizer::TakeSample() function at the point where -the pen is up and the digitizer is in the pen up debounce state (i.e. E_HW_PenUpDebounce):

if (!penDown) - { - if (iState==E_HW_PenUpDebounce) - { - . . .

At this point, you should have almost all digitizer -capability – pen up handling, pen down handling, and the taking of digitizer -readings.

Implement Ddigitizer::digitizerOff()

This -function is called when the digitizer is being powered down.

If the -device is powered on, then the function needs to do disable the digitizer -interrupt.

If the digitizer is in the collect sample state -(i.e. E_HW_CollectSample), then it also needs to do the following:

set up the hardware -so that the device wakes up from standby if the digitizer panel is touched.
relinquish the request -for power resources; this will place the peripheral hardware into a low power -"sleep" mode, which is capable of detecting an interrupt.

Implement power -up and power down handling

At this point, the device should be -working successfully.

You now need to put the device into a low power -"sleep" mode when it is switched off, and to bring it out of "sleep" mode -when the digitizer is touched.

Add code to the template -port function DTemplatedigitizer::digitizerPowerUp() to request power -resources from the power controller. This will power the device up from sleep -mode.
Add code to the powering -down part of your implementation of Ddigitizer::WaitForPenDown() that -does the following:
- sets up the hardware -to wake the device from standby if the digitizer is touched.
- relinquishes the request -for power resources - this will place the peripheral hardware into a low power -"sleep" mode, which is capable of detecting an interrupt.

+ + + + + +Channel +ImplementationDescribes how to use the template port to implement the physical +channel for the Digitizer Driver. +

Define the +size of the digitizer

The following four constants defined at the +top of the template implementation in xyin.cpp define +the origin and size of the digitizer device in pixels. Modify the values to +define your own origin and size.

const TUint KConfigXyOffsetX = 0; +const TUint KConfigXyOffsetY = 0; +const TUint KConfigXyWidth = 640; // pixels per line +const TUint KConfigXyHeight = 480; // lines per panel +

This is information that is returned when calls are made:

user side to HAL::Get() passing +the attribute(s) EPenX and EPenY
kernel side to Kern::HalFunction(), +passing group EHalGroupdigitizer and function-id EdigitizerHalXYInfo

See User-Side +Hardware Abstraction.

The following four constants define the +digitizer origin and size in digitizer ADC coordinates. Modify the values +for your own digitizer:

const Tint KConfigXySpreadX = 4096; // maximum valid X spread +const Tint KConfigXySpreadY = 4096; // maximum valid Y spread +const Tint KConfigXyMinX = 0; // minimum valid X value +const Tint KConfigXyMinY = 0; // minimum valid Y value +

Implement power +on behaviour

In the template port, this is implemented by DTemplatedigitizer::digitizerPowerUp(). +Note that this function is not derived from any base class function.

Add code to this function +to do these things:
1. Clear all digitizer +interrupts.
2. Request power resources +from the power controller. This will power the device up from sleep mode. +Note that power up, and power down, can be implemented later.
3. Configure the hardware +so that it generates an interrupt when the digitizer is touched.
Make sure that the digitizer +interrupt is defined. In the template port, the interrupt id is defined as +the constant:
const TInt KIntIddigitizer=EAsspIntIdC
in +the file ...\template\template_assp\template_assp.h.
Make sure that the interrupt +controller is configured for the digitizer interrupt. See Interrupt +Dispatcher.

Implement Ddigitizer::WaitForPenDown()

This +code is executed at startup or whenever the pen is lifted up. It implements +a request for an interrupt to be generated when the pen next touches the digitizer. +It is called by the platform independent layer:

at startup
when the pen is removed +from the digitizer after a pen-up event has been issued.

There are two main cases to deal with: the digitizer is powering +down; the digitizer is not powering down

The digitizer is powering +down

The implementation for this case can be left until later. +It is discussed in Implement +power up and power down handling.

The digitizer is not powering +down

To deal with this case, your implementation needs to:

clear the digitizer +interrupt
set up the hardware +so that it can detect when the digitizer is touched.

The pen interrupt is now enabled; if the digitizer is now touched, +the pen interrupt ISR (interrupt service routine) DTemplatedigitizer::PenInterrupt() is +called.

In the template port, the ISR includes the statement:

__KTRACE_OPT(KHARDWARE,Kern::Printf("I"));

and +means that if the KHARDWARE tracing flag has been set, and +tracing is on, then a single “I” is printed whenever the digitizer is touched.

Tracing +note

If the KEXTENSION, KPOWER and KHARDWARE tracing +flags have been set, and tracing is on, then by the time WaitForPenDown() is +called, you should be able to see the following sequence of calls in the trace:

DoCreate()
digitizerPowerUp()
WaitForPenDown()

Implement the +pen interrupt ISR

In the template port, the interrupt service routine +(ISR) that handles a pen interrupt is implemented by DTemplatedigitizer::PenInterrupt(). +Note that this function is not derived from any base class function.

There +are two main things to consider here:

You need to add code +to the start of the function to decide whether the pen is now up (i.e. removed +from the screen panel), or whether the pen is now down (i.e. touching the +digitizer panel). To make the decision, you may need to read the appropriate +hardware register. The detail depends on the hardware.
If the pen is down, +you need to check the value of the configurable constant KPenDownDelayTime. What you do next depends on the value of this constant:
- If the value is greater +than zero, then you do not need to change the code at this time. The existing +code just starts a timer to delay the beginning of the collection of samples. +Note, however, that you will need to modify the debounce timer callback function timerIntExpired() to +clear the digitizer interrupt - see Add +code to the debounce timer callback function.
- If the value is zero, +then you must clear the digitizer interrupt here in this function, PenInterrupt().

Initialise +sampling

In the template port, the initialisation of sampling is +implemented in the first half of the function DTemplatedigitizer::TakeSample() function. +Note that this function is not derived from any base class function.

There +are two main things to consider here:

You need to decide whether +the pen is up or down. Set the variable penDown to ETrue if +the pen is down or EFalse if the pen is up.

To +do this you may need to read the appropriate hardware register - the detail +depends on the hardware.
Change the section of +code that is executed when the pen is found to be up after a power on, i.e. +the block of code:
if (iState==E_HW_PowerUp) + { + if (!penDown) + { + ... + }
The block of code needs to do the following:
- reset the sample buffer
- clear the digitizer +interrupt
- set up the hardware +so that it can detect when the digitizer is touched
- enable the digitizer +interrupt.

Take sample +readings

In the template port, the initialisation of sampling is +implemented in the second half of the function DTemplatedigitizer::TakeSample() function. +Note that this function is not derived from any base class function.

This +code is executed while the pen is down, and needs to do the following:

read the hardware for +the digitizer samples and put the results into the sample buffer. The sample +buffer resides in the platform independent layer.
set up the hardware +so that it can detect when the digitizer is touched
schedule the reading +of the next sample using a one shot timer; the time interval is defined by +the value of the configurable constant KInterSampleTime
when a complete group +of samples has been taken, tell the platform independent layer by calling RawSampleValid(); +the function is a member of the base class Ddigitizer.

Tracing note

If the KHARDWARE tracing flag +has been set, and tracing is on, then it should be possible to move the pen +over the screen and see the raw sample values on the debug output. Check they +are correct.

Add code to +the debounce timer callback function

In the template port, the +debounce timer callback function is implemented by the local function timerIntExpired().

If +not already done in Implement +the pen interrupt ISR, add code to this callback function to clear +the digitizer interrupt.

Deal with a +pen up interrupt

If the digitizer generates an interrupt when the +pen is lifted, then you need to add code to the pen interrupt ISR to handle +this. This is the same function, DTemplatedigitizer::PenInterrupt(), +referred to in Implement +the pen interrupt ISR.

The code should:

clear the digitizer +interrupt.
set up the hardware +so that it can detect when the digitizer panel is touched.

If there is no pen up interrupt by design, then you need to add code +into the DTemplatedigitizer::TakeSample() function at the point where +the pen is up and the digitizer is in the pen up debounce state (i.e. E_HW_PenUpDebounce):

if (!penDown) + { + if (iState==E_HW_PenUpDebounce) + { + . . .

At this point, you should have almost all digitizer +capability – pen up handling, pen down handling, and the taking of digitizer +readings.

Implement Ddigitizer::digitizerOff()

This +function is called when the digitizer is being powered down.

If the +device is powered on, then the function needs to do disable the digitizer +interrupt.

If the digitizer is in the collect sample state +(i.e. E_HW_CollectSample), then it also needs to do the following:

set up the hardware +so that the device wakes up from standby if the digitizer panel is touched.
relinquish the request +for power resources; this will place the peripheral hardware into a low power +"sleep" mode, which is capable of detecting an interrupt.

Implement power +up and power down handling

At this point, the device should be +working successfully.

You now need to put the device into a low power +"sleep" mode when it is switched off, and to bring it out of "sleep" mode +when the digitizer is touched.

Add code to the template +port function DTemplatedigitizer::digitizerPowerUp() to request power +resources from the power controller. This will power the device up from sleep +mode.
Add code to the powering +down part of your implementation of Ddigitizer::WaitForPenDown() that +does the following:
- sets up the hardware +to wake the device from standby if the digitizer is touched.
- relinquishes the request +for power resources - this will place the peripheral hardware into a low power +"sleep" mode, which is capable of detecting an interrupt.

\ No newline at end of file