<?xml version="1.0" encoding="UTF-16"?>
<configuration xmlns="http://www.s60.com/xml/confml/1" name="wlanengine">
  <feature ref="KCRUidWlanDeviceSettings" name="WLAN Device Settings">
    <desc>Definitions for global WLAN settings.</desc>
    <setting ref="KWlanDeviceSettingsVersion" name="KWlanDeviceSettingsVersion" type="int" readOnly="true"/>
    <setting ref="KWlanBeacon" name="KWlanBeacon" type="int">
      <desc>KWlanBeacon defines the beacon interval in milliseconds to be used when creating an IBSS network. </desc>
    </setting>
    <setting ref="KWlanScanRate" name="KWlanScanRate" type="int">
      <desc>KWlanScanRate contains the data rate used for sending probe requests. The value is determined by multiplying the data rate by two; 1MB/s = 2, 2MB/s = 4 and so forth.</desc>
    </setting>
    <setting ref="KWlanRcpiTrigger" name="KWlanRcpiTrigger" type="int">
      <desc>KWlanRcpiTrigger is the RCPI threshold after which roaming to a better AP is attempted.</desc>
    </setting>
    <setting ref="KWlanMinActiveChannelTime" name="KWlanMinActiveChannelTime" type="int">
      <desc>KWlanMinActiveChannelTime is the minimum channel time for active scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanMaxActiveChannelTime" name="KWlanMaxActiveChannelTime" type="int">
      <desc>KWlanMaxActiveChannelTime is the maximum channel time for active scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanMaxTxMSDULifeTime" name="KWlanMaxTxMSDULifeTime" type="int">
      <desc>KWlanMaxTxMSDULifeTime defines the maximum amount of time allowed to transmit a packet before it is discarded. The value is in milliseconds.</desc>
    </setting>
    <setting ref="KWlanScanExpirationTimer" name="KWlanScanExpirationTimer" type="int">
      <desc>KWlanScanExpirationTimer defines how many seconds the cached broadcast scan results are valid.</desc>
    </setting>
    <setting ref="KWlanUnloadDriverTimer" name="KWlanUnloadDriverTimer" type="int">
      <desc>KWlanUnloadDriverTimer contains the activity timeout value after which the WLAN drivers are unloaded. Note that this setting applies only when the terminal is not connected to a network. The value is in seconds.</desc>
    </setting>
    <setting ref="KWlanRoamTimer" name="KWlanRoamTimer" type="int">
      <desc>KWlanRoamTimer defines how often roaming to better AP is attempted when the threshold set in KWlanRcpiTrigger has been crossed. The value is in microseconds.</desc>
    </setting>
    <setting ref="KWlanRcpiDifference" name="KWlanRcpiDifference" type="int">
      <desc>KWlanRcpiDifference defines the how much better an AP has to be than the current AP before roaming is attempted. The difference is expressed in 0.5dBm steps.</desc>
    </setting>
    <setting ref="KWlanConnRegainTimer" name="KWlanConnRegainTimer" type="int">
      <desc>KWlanConnRegainTimer is the amount of time to wait after a BSS lost indication before attempting to roam. The value is in microseconds.</desc>
    </setting>
    <setting ref="KWlanMaxTriesToFindNw" name="KWlanMaxTriesToFindNw" type="int">
      <desc>KWlanMaxTriesToFindNw contains the number of attempts to find suitable network during initial connect.</desc>
    </setting>
    <setting ref="KWlanDelayBetweenFindNw" name="KWlanDelayBetweenFindNw" type="int">
      <desc>KWlanDelayBetweenFindNw defines the amount of microseconds to wait between initial connection attempts.</desc>
    </setting>
    <setting ref="KWlanMTU" name="KWlanMTU" type="int">
      <desc>KWlanMTU is the maximum frame size in bytes the WLAN interface is allowed to send.</desc>
    </setting>
    <setting ref="KWlanMinPassiveChannelTime" name="KWlanMinPassiveChannelTime" type="int">
      <desc>KWlanMinPassiveChannelTime is the minimum channel time for passive scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanMaxPassiveChannelTime" name="KWlanMaxPassiveChannelTime" type="int">
      <desc>KWlanMaxPassiveChannelTime is the maximum channel time for passive scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanMaxApFailureCount" name="KWlanMaxApFailureCount" type="int">
      <desc>KWlanMaxApFailureCount defines the maximum amount of association failures after which the AP is internally blacklisted to avoid further attempts during the connection.</desc>
    </setting>
    <setting ref="KWlanLongBeaconFindCount" name="KWlanLongBeaconFindCount" type="int">
      <desc>KWlanLongBeaconFindCount defines the maximum number of empty consecutive IAP availability checks after which a channel known to have an AP with a long beacon interval is no longer checked for one.</desc>
    </setting>
    <setting ref="KWlanQosNullFrameInterval" name="KWlanQosNullFrameInterval" type="int">
      <desc>KWlanQosNullFrameInterval defines how often a QoS NULL data frame is sent when traffic with Voice access category is ongoing. The value is in microseconds.</desc>
    </setting>
    <setting ref="KWlanQosNullFrameTimeout" name="KWlanQosNullFrameTimeout" type="int">
      <desc>KWlanQosNullFrameTimeout is the amount of microseconds after the last Voice access category packet that QoS NULL data frame sending is stopped.</desc>
    </setting>
    <setting ref="KWlanKeepAliveInterval" name="KWlanKeepAliveInterval" type="int">
      <desc>KWlanKeepAliveInterval defines how often NULL data frames are sent when nothing is being transmitted (microseconds).</desc>
    </setting>
    <setting ref="KWlanScanStopRcpiThreshold" name="KWlanScanStopRcpiThreshold" type="int">
      <desc>KWlanScanStopRcpiThreshold defines the RCPI threshold for stopping a direct scan in a BSS lost roam.</desc>
    </setting>
    <setting ref="KWlanMinRcpiForIapAvailability" name="KWlanMinRcpiForIapAvailability" type="int">
      <desc>KWlanMinRcpiForIapAvailability is the minimum RCPI required before an IAP can be marked as available.</desc>
    </setting>
    <setting ref="KWlanQoSNullFrameEntryTimeout" name="KWlanQoSNullFrameEntryTimeout" type="int">
      <desc>Defines the time period in microseconds which is used to evaluate whether QoS NULL data frame sending should be started.</desc>
    </setting>
    <setting ref="KWlanMaxApDeauthenticationCount" name="KWlanMaxApDeauthenticationCount" type="int">
      <desc>After a successful roam an AP can deauthenticate the terminal KWlanMaxApDeauthenticationCount amount of times before it's blacklisted.</desc>
    </setting>
    <setting ref="KWlanApDeauthenticationTimeout" name="KWlanApDeauthenticationTimeout" type="int">
      <desc>Deauthentications that happen within KWlanApDeauthenticationTimeout after a successful roam are calculated towards AP's deauthentication count (microseconds).</desc>
    </setting>
    <setting ref="KWlanDefaultBGScanInterval" name="KWlanDefaultBGScanInterval" type="int" readOnly="true">
      <desc>KWlanDefaultBGScanInterval is the default value for the background scan interval in seconds.</desc>
    </setting>
    <setting ref="KWlanShowBrokenPowerSaveNote" name="KWlanShowBrokenPowerSaveNote" type="int">
      <desc>KWlanShowBrokenPowerSaveNote defines whether a note is shown to user when power save test fails during connecting to an AP.</desc>
    </setting>
    <setting ref="KWlanMaxDtimSkipInterval" name="KWlanMaxDtimSkipInterval" type="int">
      <desc>Maximum amount of microseconds to sleep when waking up on DTIMs.</desc>
    </setting>
    <setting ref="KWlanPsActiveToLightTimeout" name="KWlanPsActiveToLightTimeout" type="int">
      <desc>Time interval in microseconds after which transition from Active mode to Light PS mode is considered.</desc>
    </setting>
    <setting ref="KWlanPsActiveToLightThreshold" name="KWlanPsActiveToLightThreshold" type="int">
      <desc>Frame count threshold used when considering transition from Active to Light PS mode.</desc>
    </setting>
    <setting ref="KWlanPsLightToActiveTimeout" name="KWlanPsLightToActiveTimeout" type="int">
      <desc>Time interval in microseconds after which the frame counter used when considering transition from Light PS to Active mode is reset.</desc>
    </setting>
    <setting ref="KWlanPsLightToActiveThreshold" name="KWlanPsLightToActiveThreshold" type="int">
      <desc>Frame count threshold used when considering transition from Light PS to Active mode.</desc>
    </setting>
    <setting ref="KWlanPsLightToDeepTimeout" name="KWlanPsLightToDeepTimeout" type="int">
      <desc>Time interval in microseconds after which transition from Light PS mode to Deep PS mode is considered.</desc>
    </setting>
    <setting ref="KWlanPsLightToDeepThreshold" name="KWlanPsLightToDeepThreshold" type="int">
      <desc>Frame count threshold used when considering transition from Light PS to Deep PS mode.</desc>
    </setting>
    <setting ref="KWlanPsUapsdRxFrameLengthThreshold" name="KWlanPsUapsdRxFrameLengthThreshold" type="int">
      <desc>Received frame payload length (in bytes) threshold in U-APSD network for Best Effort Access Category.</desc>
    </setting>
    <setting ref="KWlanRcpiRoamMinInterval" name="KWlanRcpiRoamMinInterval" type="int">
      <desc>Defines the minimum delay between RCPI roam checks (in microseconds).</desc>
    </setting>
    <setting ref="KWlanRcpiRoamMaxInterval" name="KWlanRcpiRoamMaxInterval" type="int">
      <desc>Defines the maximum delay between RCPI roam checks (in microseconds).</desc>
    </setting>
    <setting ref="KWlanRcpiRoamAttemptsPerInterval" name="KWlanRcpiRoamAttemptsPerInterval" type="int">
      <desc>Defines how many times an RCPI roam check interval value is used until the next interval value is calculated.</desc>
    </setting>
    <setting ref="KWlanRcpiRoamNextIntervalFactor" name="KWlanRcpiRoamNextIntervalFactor" type="int">
      <desc>Defines the factor the current interval value is multiplied by to get the next interval value.</desc>
    </setting>
    <setting ref="KWlanRcpiRoamNextIntervalAddition" name="KWlanRcpiRoamNextIntervalAddition" type="int">
      <desc>Defines the value that is added to the interval value that has been multiplied by KWlanRcpiRoamNextIntervalFactor.</desc>
    </setting>
    <setting ref="KWlanScanListExpirationTime" name="KWlanScanListExpirationTime" type="int">
      <desc>Defines how long beacons/probe responses are stored in the internal scan list (in microseconds).</desc>
    </setting>
    <setting ref="KWlanQoSNullFrameEntryTxCount" name="KWlanQoSNullFrameEntryTxCount" type="int">
      <desc>Defines how many Voice AC packets must be sent during a certain period before QoS NULL data frame sending is started.</desc>
    </setting>
    <setting ref="KWlanSpRcpiTarget" name="KWlanSpRcpiTarget" type="int">
      <desc>Defines the signal predictor algorithm target RCPI value for roam indication.</desc>
    </setting>
    <setting ref="KWlanSpTimeTarget" name="KWlanSpTimeTarget" type="int">
      <desc>Defines the signal predictor algorithm target time for roam indication (in microseconds).</desc>
    </setting>
    <setting ref="KWlanSpMinIndicationInterval" name="KWlanSpMinIndicationInterval" type="int">
      <desc>Defines the minimum time interval for consecutive roam indications from the signal predictor algorithm (in microseconds).</desc>
    </setting>
    <setting ref="KWlanBssLostRoamMinInterval" name="KWlanBssLostRoamMinInterval" type="int">
      <desc>Defines the minimum delay between BSS lost roam attempts (in microseconds).</desc>
    </setting>
    <setting ref="KWlanBssLostRoamMaxInterval" name="KWlanBssLostRoamMaxInterval" type="int">
      <desc>Defines the maximum delay between BSS lost roam attempts (in microseconds).</desc>
    </setting>
    <setting ref="KWlanBssLostRoamAttemptsPerInterval" name="KWlanBssLostRoamAttemptsPerInterval" type="int">
      <desc>Defines how many times a BSS lost roam interval value is used until the next interval value is calculated.</desc>
    </setting>
    <setting ref="KWlanBssLostRoamNextIntervalFactor" name="KWlanBssLostRoamNextIntervalFactor" type="int">
      <desc>Defines the factor the current interval value is multiplied by to get the next interval value.</desc>
    </setting>
    <setting ref="KWlanBssLostRoamNextIntervalAddition" name="KWlanBssLostRoamNextIntervalAddition" type="int">
      <desc>Defines the value that is added to the interval value that has been multiplied by KWlanBssLostRoamNextIntervalFactor.</desc>
    </setting>
    <setting ref="KWlanBssLostRoamMaxTriesToFindNw" name="KWlanBssLostRoamMaxTriesToFindNw" type="int">
      <desc>Defines how many attempts are made to find a suitable AP before giving up during BSS lost.</desc>
    </setting>
    <setting ref="KWlanTrafficStreamCreationTimeout" name="KWlanTrafficStreamCreationTimeout" type="int">
      <desc>Defines how many microseconds to wait for traffic stream request response.</desc>
    </setting>
    <setting ref="KWlanBeaconLostThreshold" name="KWlanBeaconLostThreshold" type="int">
      <desc>Defines the number of lost consecutive beacons after which beacon lost event is indicated.</desc>
    </setting>
    <setting ref="KWlanBtBeaconLostThreshold" name="KWlanBtBeaconLostThreshold" type="int">
      <desc>Defines the number of lost consecutive beacons after which beacon lost event is indicated during an active Bluetooth connection.</desc>
    </setting>
    <setting ref="KWlanTxFailThreshold" name="KWlanTxFailThreshold" type="int">
      <desc>Defines the number of lost consecutive packets after which TX failure event is indicated.</desc>
    </setting>
    <setting ref="KWlanBtTxFailThreshold" name="KWlanBtTxFailThreshold" type="int">
      <desc>Defines the number of lost consecutive packets after which TX failure event is indicated during an active Bluetooth connection.</desc>
    </setting>
    <setting ref="KWlanPowerSaveDelay" name="KWlanPowerSaveDelay" type="int">
      <desc>Defines the number of seconds after which power save is enabled during the initial association.</desc>
    </setting>
    <setting ref="KWlanRegionExpirationTime" name="KWlanRegionExpirationTime" type="int" readOnly="true">
      <desc>Defines the amount of seconds region information is valid.</desc>
    </setting>
    <setting ref="KWlanRrmMinMeasurementInterval" name="KWlanRrmMinMeasurementInterval" type="int">
      <desc>Defines the minimum interval for accepting subsequent RRM Beacon Requests (in microseconds).</desc>
    </setting>
    <setting ref="KWlanPsmSrvMode" name="KWlanPsmSrvMode" type="int">
      <desc>Current PSM server mode where possible values are: 0 = Normal mode, 1 = Power save, 2 = Partial power save</desc>
    </setting>
    <setting ref="KWlanBgScanPeakTimeStart" name="KWlanBgScanPeakTimeStart" type="int">
      <desc>Start time for WLAN background scan peak period specifying hours and minutes. alid range is 0 to 2359 meaning 00:00 o'clock to 23:59 o'clock.</desc>
    </setting>
    <setting ref="KWlanBgScanPeakTimeEnd" name="KWlanBgScanPeakTimeEnd" type="int">
      <desc>End time for WLAN background scan peak period specifying hours and minutes. Valid range is 0 to 2359 meaning 00:00 o'clock to 23:59 o'clock.</desc>
    </setting>
    <setting ref="KWlanBgScanIntervalPeakPeriod" name="KWlanBgScanIntervalPeakPeriod" type="int">
      <desc>WLAN background scan interval in seconds for peak period</desc>
    </setting>
    <setting ref="KWlanBgScanIntervalOffPeakPeriod" name="KWlanBgScanIntervalOffPeakPeriod" type="int">
      <desc>WLAN background scan interval in seconds for off-peak period.</desc>
    </setting>
    <setting ref="KWlanAutomaticTrafficStreamMgmt" name="KWlanAutomaticTrafficStreamMgmt" type="int">
      <desc>Defines whether admission control traffic stream management is done automatically.</desc>
    </setting>
    <setting ref="KWlanMinActiveBroadcastChannelTime" name="KWlanMinActiveBroadcastChannelTime" type="int">
      <desc>KWlanMinActiveBroadcastChannelTime is the minimum channel time for active broadcast scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanMaxActiveBroadcastChannelTime" name="KWlanMaxActiveBroadcastChannelTime" type="int">
      <desc>KWlanMaxActiveBroadcastChannelTime is the maximum channel time for active broadcast scan in milliseconds.</desc>
    </setting>
    <setting ref="KWlanRegion" name="KWlanRegion" type="int" readOnly="true">
      <desc>KWlanRegion is the last known WLAN region information that is valid for 5 hours. This value is selected based on the information received from APs or from cellular network (mobile country code). Possible values: 0 = region is unknown, 1 = region is ETSI, 2 = region is FCC.</desc>
    </setting>
    <setting ref="KWlanRegionTimestamp" name="KWlanRegionTimestamp" type="int" readOnly="true">
      <desc>KWlanRegionTimestamp is the timestamp for storing the latest WLAN region (KWlanRegion) (minutes from 0AD nominal Gregorian).</desc>
    </setting>
  </feature>
  <feature ref="KWlanEnabledFeatures" name="Enabled WLAN Features">
    <setting ref="KWlanFeature802p11n" name="802.11n" type="boolean">
      <desc>If OFF, 802.11n functionality is disabled.</desc>
    </setting>
  </feature>
  <data>
    <KCRUidWlanDeviceSettings>
      <KWlanDeviceSettingsVersion>1</KWlanDeviceSettingsVersion>
      <KWlanBeacon>100</KWlanBeacon>
      <KWlanScanRate>2</KWlanScanRate>
      <KWlanRcpiTrigger>70</KWlanRcpiTrigger>
      <KWlanMinActiveChannelTime>10</KWlanMinActiveChannelTime>
      <KWlanMaxActiveChannelTime>30</KWlanMaxActiveChannelTime>
      <KWlanMaxTxMSDULifeTime>512</KWlanMaxTxMSDULifeTime>
      <KWlanScanExpirationTimer>7</KWlanScanExpirationTimer>
      <KWlanUnloadDriverTimer>1</KWlanUnloadDriverTimer>
      <KWlanRoamTimer>7000000</KWlanRoamTimer>
      <KWlanRcpiDifference>12</KWlanRcpiDifference>
      <KWlanConnRegainTimer>10000000</KWlanConnRegainTimer>
      <KWlanMaxTriesToFindNw>5</KWlanMaxTriesToFindNw>
      <KWlanDelayBetweenFindNw>1500000</KWlanDelayBetweenFindNw>
      <KWlanMTU>1500</KWlanMTU>
      <KWlanMinPassiveChannelTime>110</KWlanMinPassiveChannelTime>
      <KWlanMaxPassiveChannelTime>110</KWlanMaxPassiveChannelTime>
      <KWlanMaxApFailureCount>5</KWlanMaxApFailureCount>
      <KWlanLongBeaconFindCount>3</KWlanLongBeaconFindCount>
      <KWlanQosNullFrameInterval>20000</KWlanQosNullFrameInterval>
      <KWlanQosNullFrameTimeout>1000000</KWlanQosNullFrameTimeout>
      <KWlanKeepAliveInterval>60000000</KWlanKeepAliveInterval>
      <KWlanScanStopRcpiThreshold>80</KWlanScanStopRcpiThreshold>
      <KWlanMinRcpiForIapAvailability>50</KWlanMinRcpiForIapAvailability>
      <KWlanQoSNullFrameEntryTimeout>300000</KWlanQoSNullFrameEntryTimeout>
      <KWlanMaxApDeauthenticationCount>5</KWlanMaxApDeauthenticationCount>
      <KWlanApDeauthenticationTimeout>2000000</KWlanApDeauthenticationTimeout>
      <KWlanDefaultBGScanInterval>300</KWlanDefaultBGScanInterval>
      <KWlanShowBrokenPowerSaveNote>1</KWlanShowBrokenPowerSaveNote>
      <KWlanMaxDtimSkipInterval>0</KWlanMaxDtimSkipInterval>
      <KWlanPsActiveToLightTimeout>100000</KWlanPsActiveToLightTimeout>
      <KWlanPsActiveToLightThreshold>1</KWlanPsActiveToLightThreshold>
      <KWlanPsLightToActiveTimeout>300000</KWlanPsLightToActiveTimeout>
      <KWlanPsLightToActiveThreshold>4</KWlanPsLightToActiveThreshold>
      <KWlanPsLightToDeepTimeout>1000000</KWlanPsLightToDeepTimeout>
      <KWlanPsLightToDeepThreshold>1</KWlanPsLightToDeepThreshold>
      <KWlanPsUapsdRxFrameLengthThreshold>400</KWlanPsUapsdRxFrameLengthThreshold>
      <KWlanRcpiRoamMinInterval>4000000</KWlanRcpiRoamMinInterval>
      <KWlanRcpiRoamMaxInterval>60000000</KWlanRcpiRoamMaxInterval>
      <KWlanRcpiRoamAttemptsPerInterval>2</KWlanRcpiRoamAttemptsPerInterval>
      <KWlanRcpiRoamNextIntervalFactor>2</KWlanRcpiRoamNextIntervalFactor>
      <KWlanRcpiRoamNextIntervalAddition>0</KWlanRcpiRoamNextIntervalAddition>
      <KWlanScanListExpirationTime>120000000</KWlanScanListExpirationTime>
      <KWlanQoSNullFrameEntryTxCount>5</KWlanQoSNullFrameEntryTxCount>
      <KWlanSpRcpiTarget>65</KWlanSpRcpiTarget>
      <KWlanSpTimeTarget>900000</KWlanSpTimeTarget>
      <KWlanSpMinIndicationInterval>3000000</KWlanSpMinIndicationInterval>
      <KWlanBssLostRoamMinInterval>1000000</KWlanBssLostRoamMinInterval>
      <KWlanBssLostRoamMaxInterval>1500000</KWlanBssLostRoamMaxInterval>
      <KWlanBssLostRoamAttemptsPerInterval>2</KWlanBssLostRoamAttemptsPerInterval>
      <KWlanBssLostRoamNextIntervalFactor>1</KWlanBssLostRoamNextIntervalFactor>
      <KWlanBssLostRoamNextIntervalAddition>500000</KWlanBssLostRoamNextIntervalAddition>
      <KWlanBssLostRoamMaxTriesToFindNw>5</KWlanBssLostRoamMaxTriesToFindNw>
      <KWlanTrafficStreamCreationTimeout>1000000</KWlanTrafficStreamCreationTimeout>
      <KWlanBeaconLostThreshold>15</KWlanBeaconLostThreshold>
      <KWlanBtBeaconLostThreshold>20</KWlanBtBeaconLostThreshold>
      <KWlanTxFailThreshold>4</KWlanTxFailThreshold>
      <KWlanBtTxFailThreshold>4</KWlanBtTxFailThreshold>
      <KWlanPowerSaveDelay>7</KWlanPowerSaveDelay>
      <KWlanRegionExpirationTime>18000</KWlanRegionExpirationTime>
      <KWlanRrmMinMeasurementInterval>45000000</KWlanRrmMinMeasurementInterval>
      <KWlanPsmSrvMode>0</KWlanPsmSrvMode>
      <KWlanBgScanPeakTimeStart>600</KWlanBgScanPeakTimeStart>
      <KWlanBgScanPeakTimeEnd>100</KWlanBgScanPeakTimeEnd>
      <KWlanBgScanIntervalPeakPeriod>600</KWlanBgScanIntervalPeakPeriod>
      <KWlanBgScanIntervalOffPeakPeriod>1200</KWlanBgScanIntervalOffPeakPeriod>
      <KWlanAutomaticTrafficStreamMgmt>1</KWlanAutomaticTrafficStreamMgmt>
      <KWlanMinActiveBroadcastChannelTime>10</KWlanMinActiveBroadcastChannelTime>
      <KWlanMaxActiveBroadcastChannelTime>110</KWlanMaxActiveBroadcastChannelTime>      
      <KWlanRegion>0</KWlanRegion>
      <KWlanRegionTimestamp>0</KWlanRegionTimestamp>
    </KCRUidWlanDeviceSettings>
    <KWlanEnabledFeatures>
      <KWlanFeature802p11n>true</KWlanFeature802p11n>
    </KWlanEnabledFeatures>
  </data>
  <rfs>
    <KCRUidWlanDeviceSettings>
      <KWlanDefaultBGScanInterval>true</KWlanDefaultBGScanInterval>
    </KCRUidWlanDeviceSettings>
  </rfs>
</configuration>
