;/*

;* Copyright (c) 2009 Nokia Corporation and/or its subsidiary(-ies).

;* All rights reserved.

;* This component and the accompanying materials are made available

;* under the terms of the License "Eclipse Public License v1.0"

;* which accompanies this distribution, and is available

;* at the URL "http://www.eclipse.org/legal/epl-v10.html".

;*

;* Initial Contributors:

;* Nokia Corporation - initial contribution.

;*

;* Contributors:

;*

;* Description:

;*

;*/

		GBLL	__VARIANT_S__       ; indicates that this is platform-specific code

		GBLL	__SYBORG_S__		; indicates which source file this is

		INCLUDE	bootcpu.inc

		INCLUDE syborg.inc

;

;*******************************************************************************

;

        IMPORT	ResetEntry

;

;*******************************************************************************

;

        AREA |Boot$$Code|, CODE, READONLY, ALIGN=6

;

;*******************************************************************************

; Initialise Hardware

;	Determine the hardware configuration

;	Determine the reset reason. If it is wakeup from a low power mode, perform

;		whatever reentry sequence is required and jump back to the kernel.

;	Set up the memory controller so that at least some RAM is available

;	Set R10 to point to the super page or to a temporary version of the super page

;		with at least the following fields valid:

;		iBootTable, iCodeBase, iActiveVariant, iCpuId

;	Initialise the debug serial port

;

; Enter with:

;	R12 points to TRomHeader

;	NO STACK

;	R14 = return address (as usual)

;

; All registers may be modified by this call

;*******************************************************************************

	EXPORT	InitialiseHardware

InitialiseHardware	ROUT

		mov		r13, lr							    ; save return address

		adrl	r1, ParameterTable	        ; pass address of parameter table

		bl		InitCpu				        ; initialise CPU/MMU registers

;*******************************************************************************

; DoInitialise Hardware

;	Initialise CPU registers

;	Determine the hardware configuration

;	Determine the reset reason. If it is wakeup from a low power mode, perform

;		whatever reentry sequence is required and jump back to the kernel.

;	Set up the memory controller so that at least some RAM is available

;	Set R10 to point to the super page or to a temporary version of the super page

;		with at least the following fields valid:

;		iBootTable, iCodeBase, iActiveVariant, iCpuId

;	In debug builds initialise the debug serial port

;

; Enter with:

;	R12 points to TRomHeader

;	NO STACK

;	R13 = return address (as usual)

;

; All registers may be modified by this call

;*******************************************************************************

DoInitialiseHardware	ROUT

; Hardware memory size is 128MB - 32MB reserved for bootloader

		mov		r4, #KHwRamSizeMb

		bl		InitDebugPort

		ldr		r7, =CFG_HWVD					; variant number

		lsl		r10, r4, #20				    ; R10 = top of RAM

		sub		r10, #0x2000				    ; put super page at end for now

; Set up the required super page values

		str		r7, [r10, #SSuperPageBase_iActiveVariant]

		mov		r1, #0

		str		r1, [r10, #SSuperPageBase_iHwStartupReason]	; reset reason (from hardware)

		add		r1, r10, #CpuPageOffset

		str		r1, [r10, #SSuperPageBase_iMachineData]

		bl		GetBootTableAddress

		str		r0, [r10, #SSuperPageBase_iBootTable]		; set the boot function table

		str		r12, [r10, #SSuperPageBase_iCodeBase]		; set the base address of bootstrap code

		mrc		p15, 0, r0, c0, c0, 0						; read CPU ID from CP15 (remove if no CP15)

		str		r0, [r10, #SSuperPageBase_iCpuId]

		mov		r0, r13

		add		sp, r10, #CpuBootStackTop		            ; set up a boot stack

		push    {r0}						                ; save return address

		bl		DoInitHw2						            ; any extra CPU-dependent stuff

		ldr		r7, [r10, #SSuperPageBase_iActiveVariant]

		DWORD	r7, "ActiveVariant"

		pop     {pc}						                ; return

;*******************************************************************************

DoInitHw2	ROUT

		mrc		p15, 0, r0, c0, c0, 0

		DWORD	r0, "MMUID"

		mrc		p15, 0, r0, c0, c0, 1

		DWORD	r0, "CacheType"

		mrc		p15, 0, r0, c0, c0, 2

		DWORD	r0, "TCMType"

		mrc		p15, 0, r0, c0, c0, 3

		DWORD	r0, "TLBType"

        bx      lr

;*******************************************************************************

; Get a pointer to the list of hardware banks

;

; The pointer returned should point to a list of hardware banks declared with

; the HW_MAPPING and/or HW_MAPPING_EXT macros. A zero word terminates the list.

; For the direct memory model, all hardware on the system should be mapped here

; and the mapping will set linear address = physical address.

; For the moving or multiple model, only the hardware required to boot the kernel

; and do debug tracing needs to be mapped here. The linear addresses used will

; start at KPrimaryIOBase and step up as required with the order of banks in

; the list being maintained in the linear addresses used.

;

; HW_MAPPING PB, SIZE, MULT

;	This declares a block of I/O with physical base PB and address range SIZE

;	blocks each of which has a size determined by MULT. The page size used for

;	the mapping is determined by MULT. The linear address base of the mapping

;	will be the next free linear address rounded up to the size specified by

;	MULT.

;	The permissions used for the mapping are the standard I/O permissions (BTP_Hw).

;

; HW_MAPPING_EXT PB, SIZE, MULT

;	This declares a block of I/O with physical base PB and address range SIZE

;	blocks each of which has a size determined by MULT. The page size used for

;	the mapping is determined by MULT. The linear address base of the mapping

;	will be the next free linear address rounded up to the size specified by

;	MULT.

;	The permissions used for the mapping are determined by a BTP_ENTRY macro

;	immediately following this macro in the HW bank list or by a DCD directive

;	specifying a different standard permission type.

;

; Configurations without an MMU need not implement this function.

;

; Enter with :

;		R10 points to super page

;		R12 points to ROM header

;		R13 points to valid stack

;

; Leave with :

;		R0 = pointer

;		Nothing else modified

;*******************************************************************************

	EXPORT	GetHwBanks

GetHwBanks	ROUT

		adr		r0, %FT1

		bx      lr

1

		HW_MAPPING		KHwBaseSic,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseRtc,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseTimer,			1,	HW_MULT_4K	

		HW_MAPPING		KHwBaseKmiKeyboard,		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseKmiPointer,		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseClcd,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseUart0,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseUart1,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseUart2,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseUart3,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseHostFs,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseSnap,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseNet,			1,	HW_MULT_4K

		HW_MAPPING		KHwBaseNand,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseAudio,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBaseWebcamera,    		1,	HW_MULT_4K

		HW_MAPPING		KHwBasePlatform,    		8,	HW_MULT_4K

		DCD     0   ; terminator

;*******************************************************************************

; Notify an unrecoverable error during the boot process

;

; Enter with:

;	R14 = address at which fault detected

;

; Don't return

;*******************************************************************************

	EXPORT	Fault

Fault	ROUT

		b		BasicFaultHandler	; generic handler dumps registers via debug

									; serial port

;*******************************************************************************

; Reboot the system

;

; Enter with:

;		R0 = reboot reason code

;

; Don't return (of course)

;*******************************************************************************

	ALIGN	32, 0

	EXPORT	RestartEntry

RestartEntry	ROUT

; Save R0 parameter in HW dependent register which is preserved over reset

; Put HW specific code here to reset system

	    GETCPSR	r1

		orr		r1, #0xC0

		SETCPSR	r1										; disable interrupts

        ldr     r10, =KSuperPageLinAddr

        adr     r0, Run_Physical

        bl      RomLinearToPhysical                 ; physical address in r0

; Disable MMU

		mrc		p15, 0, r1, c1, c0, 0		        ; get MMUCR

		bic		r1, #MMUCR_M		                ; clear M bit

		mcr		p15, 0, r1, c1, c0, 0		        ; set MMUCR

        bx      r0                                  ; jump to the physical address

; Now running from physical address

Run_Physical

        mov     r3, #KHwNorFlashBaseAddr            ; r3 = NOR flash image base

; Jump to the NOR flash image

        bx      r3                              

;*******************************************************************************

; Get a pointer to the list of RAM banks

;

; The pointer returned should point to a list of {BASE; MAXSIZE;} pairs, where

; BASE is the physical base address of the bank and MAXSIZE is the maximum

; amount of RAM which may be present in that bank. MAXSIZE should be a power of

; 2 and BASE should be a multiple of MAXSIZE. The generic code will examine the

; specified range of addresses and determine the actual amount of RAM if any

; present in the bank. The list is terminated by an entry with zero size.

;

; The pointer returned will usually be to constant data, but could equally well

; point to RAM if dynamic determination of the list is required.

;

; Enter with :

;		R10 points to super page

;		R12 points to ROM header

;		R13 points to valid stack

;

; Leave with :

;		R0 = pointer

;		Nothing else modified

;*******************************************************************************

	EXPORT	GetRamBanks

GetRamBanks	ROUT

	    push    {r1-r3,lr}

		mov		r0, #KHwRamSizeMb

		lsl		r2, r0, #20			    ; R2 = RAM size in bytes

		mov		r1, #KHwRamBaseAddr		; R1 = base address of usable RAM area

		sub		r2, r1				    ; R2 = size of usable RAM area

		orr		r1, #RAM_VERBATIM   	; prevent testing (overlay would break it)

		mov		r3, #0

		mov		lr, #0					; terminator

		add		r0, r10, #CpuPageOffset	;

		stm	    r0, {r1-r3,lr}			; store single bank descriptor and terminator

		pop     {r1-r3,pc}

;*******************************************************************************

; Get a pointer to the list of ROM banks

;

; The pointer returned should point to a list of entries of SRomBank structures,

; usually declared with the ROM_BANK macro.

; The list is terminated by a zero size entry (four zero words)

;

; ROM_BANK	PB, SIZE, LB, W, T, RS, SS

; PB = physical base address of bank

; SIZE = size of bank

; LB = linear base if override required - usually set this to 0

; W = bus width (ROM_WIDTH_8, ROM_WIDTH_16, ROM_WIDTH_32)

; T = type (see TRomType enum in kernboot.h)

; RS = random speed

; SS = sequential speed

;

; Only PB, SIZE, LB are used by the rest of the bootstrap.

; The information given here can be modified by the SetupRomBank call, if

; dynamic detection and sizing of ROMs is required.

;

; Enter with :

;		R10 points to super page

;		R12 points to ROM header

;		R13 points to valid stack

;

; Leave with :

;		R0 = pointer

;		Nothing else modified

;*******************************************************************************

	EXPORT	GetRomBanks

GetRomBanks	ROUT

        adr		r0, RomBanksFlashTable      ; NOR flash

        bx      lr

RomBanksFlashTable

		ROM_BANK	KHwNorFlashBaseAddr, KHwNorFlashCodeSize, 0, ROM_WIDTH_32, ERomTypeXIPFlash, 0, 0

		DCD		0,0,0,0			; terminator

;*******************************************************************************

; Set up RAM bank

;

; Do any additional RAM controller initialisation for each RAM bank which wasn't

; done by InitialiseHardware.

; Called twice for each RAM bank :-

;	First with R3 = 0xFFFFFFFF before bank has been probed

;	Then, if RAM is present, with R3 indicating validity of each byte lane, ie

;	R3 bit 0=1 if D0-7 are valid, bit1=1 if D8-15 are valid etc.

; For each call R1 specifies the bank physical base address.

;

; Enter with :

;		R10 points to super page

;		R12 points to ROM header

;		R13 points to stack

;		R1 = physical base address of bank

;		R3 = width (bottom 4 bits indicate validity of byte lanes)

;			 0xffffffff = preliminary initialise

;

; Leave with :

;		No registers modified

;*******************************************************************************

	EXPORT	SetupRamBank

SetupRamBank	ROUT

		bx      lr

;*******************************************************************************

; Set up ROM bank

;

; Do any required autodetection and autosizing of ROMs and any additional memory

; controller initialisation for each ROM bank which wasn't done by

; InitialiseHardware.

;

; The first time this function is called R11=0 and R0 points to the list of

; ROM banks returned by the BTF_RomBanks call. This allows any preliminary setup

; before autodetection begins.

;

; This function is subsequently called once for each ROM bank with R11 pointing

; to the current information held about that ROM bank (SRomBank structure).

; The structure pointed to by R11 should be updated with the size and width

; determined. The size should be set to zero if there is no ROM present in the

; bank.

;

; Enter with :

;		R10 points to super page

;		R12 points to ROM header

;		R13 points to stack

;		R11 points to SRomBank info for this bank

;		R11 = 0 for preliminary initialise (all banks)

;

; Leave with :

;		Update SRomBank info with detected size/width

;		Set the size field to 0 if the ROM bank is absent

;		Can modify R0-R4 but not other registers

;

;*******************************************************************************

	EXPORT	SetupRomBank

SetupRomBank	ROUT						    ; only get here if running from ROM

		cmp		r11, #0

		bxeq	lr						        ; don't do anything for preliminary

		ldm	    r11, {r0,r1}				    ; r0 = base, r1 = size

        lsr     r0, pc, #20

        lsl     r0, #20                         ; r0 = image base

   		ldr		r1, [r12, #TRomHeader_iRomSize] ; r1 = size of ROM block

		stm 	r11, {r0,r1}

        bx      lr

;*******************************************************************************

; Reserve physical memory

;

; Reserve any physical RAM needed for platform-specific purposes before the

; bootstrap begins allocating RAM for page tables/kernel data etc.

;

; There are two methods for this:

;	1.	The function ExciseRamArea may be used. This will remove a contiguous

;		region of physical RAM from the RAM bank list. That region will never

;		again be identified as RAM.

;	2.	A list of excluded physical address ranges may be written at [R11].

;		This should be a list of (base,size) pairs terminated by a (0,0) entry.

;		This RAM will still be identified as RAM by the kernel but will not

;		be allocated by the bootstrap and will subsequently be marked as

;		allocated by the kernel immediately after boot.

;

; Enter with :

;		R10 points to super page

;		R11 indicates where preallocated RAM list should be written.

;		R12 points to ROM header

;		R13 points to stack

;

; Leave with :

;		R0-R3 may be modified. Other registers should be preserved.

;*******************************************************************************

	EXPORT	ReservePhysicalMemory

ReservePhysicalMemory	ROUT

		bx      lr

;*******************************************************************************

; Do final platform-specific initialisation before booting the kernel

;

; Typical uses for this call would be:

;	1.	Mapping cache flushing areas

;	2.	Setting up pointers to routines in the bootstrap which are used by

;		the variant or drivers (eg idle code).

;

; Enter with :

;		R10 points to super page

;		R11 points to TRomImageHeader for the kernel

;		R12 points to ROM header

;		R13 points to stack

;

; Leave with :

;		R0-R9 may be modified. Other registers should be preserved.

;

;*******************************************************************************

	EXPORT	FinalInitialise

FinalInitialise ROUT

		bx      lr

;*******************************************************************************

; Debug port write routine associated with debug port in the super page

; Enter with :

;		R0  character to be written

;		R12 points to rom header

;		R13 points to valid stack

;

; Leave with :

;		nothing modified 

;*******************************************************************************

	EXPORT	DoWriteC

DoWriteC	ROUT

	IF	CFG_DebugBootRom

		push    {r1,lr}

		bl		GetDebugPortBase			; r1 = base address of UART registers

		str		r0, [r1, #4]				; Store to data register

		pop     {r1,pc}

	ELSE

		bx      lr

	ENDIF

;*******************************************************************************

; Initialise the debug port

;

; Enter with :

;		R12 points to ROM header

;		There is no valid stack

;

; Leave with :

;		R0-R2 modified

;		Other registers unmodified

;*******************************************************************************

InitDebugPort	ROUT

		GET_ADDRESS	r1, KHwBaseUart0, KHwLinBaseUart0

		ldr		r0,[r1, #0]		

		bx		lr

;*******************************************************************************

; Get the base address of the debug UART

;

; Enter with :

;		R12 points to ROM header

;		There may be no stack

;

; Leave with :

;		R1 = base address of port, 0 for JTAG

;		Z flag set for JTAG, clear for non-JTAG

;		No other registers modified

;*******************************************************************************

GetDebugPortBase	ROUT

		ldr		r1, [r12, #TRomHeader_iDebugPort]

		cmp		r1, #42							; JTAG?

		bxeq	lr							    ; yes - return 0 and set Z

		cmp		r1, #1

        blo     GetUartPort0          

        beq     GetUartPort1

		cmp		r1, #3

        blo     GetUartPort2

		beq		GetUartPort3

GetUartPort0

		GET_ADDRESS	r1, KHwBaseUart0, KHwLinBaseUart0

		movs	r1, r1							; clear Z

		bx      lr

GetUartPort1

		GET_ADDRESS	r1, KHwBaseUart1, KHwLinBaseUart1

		movs	r1, r1							; clear Z

		bx      lr

GetUartPort2

		GET_ADDRESS	r1, KHwBaseUart2, KHwLinBaseUart2

		movs	r1, r1							; clear Z

		bx      lr

GetUartPort3

		GET_ADDRESS	r1, KHwBaseUart3, KHwLinBaseUart3

		movs	r1, r1							; clear Z

		bx      lr

;*******************************************************************************

; Return parameter specified by R0 (see TBootParam enum)

;

; Enter with :

;		R0 = parameter number

;

; Leave with :

;		If parameter value is supplied, R0 = value and N flag clear

;		If parameter value is not supplied, N flag set. In this case the

;		parameter may be defaulted or the system may fault.

;		R0, R1 modified. No other registers modified.

;

;*******************************************************************************

GetParameters ROUT

		adr		r1, ParameterTable

		b		FindParameter