# This is the global environment file to configure the touch-screen test suite on a specific device

# The current default touch screen test suite values are configured for TI OMAP 2420 (H4) hardware digitiser device

# Licencees may need to configure below values to specific devices and also where applicable,

# check supported HAL Enum's

[generic]

# A timeout value in microseconds. 

# This is a 10 second timeout used in the manual testcases

minTimeout                      =1000000

# A timeout value in microseconds. 

# This is a 50 second timeout used in the manual testcases

maxTimeout                      =5000000

# Defines the error margin in pixels that the digitiser test suite will cater for.

errorMargin                     =10

# A hexadecimal value used to represent keycode values used in tests where manual confirmation 

# is required via a key press. 

# The keycode value represents the TKeyCode enum value, by default the hexadecimal value

# used in this suite is the 'one' key.

# (Please note that some of these mappings are device dependant).

keyCode                         =0x0031

[confirm]

instructions                    =Press the number one key to pass the test case. Any key to fail.

[exitBox]

# Defines the horizontal co-ordinate value for the positioning of the exit box.

minX                      =10

# Defines the vertical co-ordinate  value for the positioning of the exit box.

minY                      =100

# Defines the horizontal co-ordinate value for the positioning of the exit box.

maxX                      =40

# Defines the vertical co-ordinate  value for the positioning of the exit box.

maxY                      =120

[randomPixels]

# Defaults values used in the scenario where the user has

# to touch any pixel on the screen with a stylus, and manually confirm if a test has passed.

instructions                    =Touch any number of screen pixels randomly with stylus. To exit testcase hit the exit box.

pixelfeedback                   =Did the pixels hightlight correctly? Press the number one key to pass the test case. Any key to fail.

# Defines the number of pixels that will need to be verified. In the default scenario we are using -1 to indicate an unlimited number of 

# pixels, for example here the use of the number 3 would indicate three pixels to verify.

pointsTotal                     =-1

[randomLine]

instructions                    =Draw a straight line from any point to any point. To exit testcase hit the exit box.

pixelfeedback                   =Did correct pixels hightlight? Press the number one key to pass the test case. Any key to fail.

# Defines the number of pixels that will need to be verified. In the default scenario we are using -1 to indicate an unlimited number of 

# pixels

pointsTotal                     =3

[preDrawnDots]

# Defaults values used in the scenario when pixels are predrawn on the screen, and the user has

# to touch each pixel with a stylus.

instructions                    =Touch the inside the drawn rectangle. To exit testcase hit the exit box

# Defines the number of pixels that will be predrawn on the screen ready to verify.

pointsTotal                     =3

# Define the predrawn co-ordinates here there are 3 but this can be increased by adding further values

# i.e 4_x and so forth

1_x		                =30

1_y		                =210

2_x		                =180

2_y		                =60

3_x		                =200

3_y		                =300

[preDrawnRect]

# Defaults values used in the scenario when pixels are predrawn on the screen, and the user has

# to touch each pixel with a stylus.

instructions                    =With stylus, draw a line within this box. To exit testcase hit the exit box

# Defines the number of pixels that will be predrawn on the screen ready to verify

eventTotal                     =3

# Default values used in the scenario where a line is predrawn on the screen, and the user has

# to follow the line with a stylus. the values below indicate the defualt Top left and bottom right of that rect

tl_x                             =80

tl_y                             =180

br_x                             =200

br_y                             =200

[colour]

# The mask value of the colour black

black                           =0x00

# The mask value of the colour white

white                           =0xFF

[displayMode]

# Define  the mode display mode for the  screen to use in these tests

value                           ={displayMode,defaultmode}  

expected                        ={displayMode,defaultmode} 

# Define  the default mode display mode for the  screen

defaultmode                     ={displayMode,mode3}  

# Define  display mode for the  screen

mode0                           =0

# Define  display mode for the  screen

mode1                           =1

# Define  display mode for the  screen

mode2                           =2

# Define  display mode for the  screen

mode3                           =7

# Define  display mode for the  screen

mode4                           =4

[haldata]

# Default value of the the pen/digitizer horizontal resolution, in pixels

ePenXValue                     =365

# Default value of the pen/digitizer vertical resolution, in pixels.

ePenYValue                     =280

[halDataOff]

# Default value of the the HAL Data to set or get. 

value                   =0

expected                =0

[halDataOn]

# Default value of the the HAL Data to set or get

value                   =1

expected                =1

[rawEvent]

# Defines the Enum strings used by TRawEvent.

# Represents an uninitialised event object.

none                            =ENone     

# EPointerMove A pointer device (e.g. a pen) has moved. Only changes in Cartesian coordinates are tracked.

pointerMove  		        =EPointerMove

# A switch on event caused by a screen tap using a pointer device.

pointerSwitchOn                 =EPointerSwitchOn 

# Represents a keyboard key down event. 

keyDown                         =EKeyDown 

#Represents a keyboard key up event.

keyUp                           =EKeyUp 

# Represents a redraw event.

redraw                          =ERedraw 

# Represents a device switch on event.

switchOn                        =ESwitchOn 

active                          =EActive 

inactive                        =EInactive 

# Represents a modifier key being pressed.

updateModifiers                 =EUpdateModifiers

# Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen

button1Down  		       =EButton1Down

# Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen.

button1Up                       =EButton1Up

# Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen.

button2Down                    =EButton2Down 

# Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen.

button2Up                      =EButton2Up 

# Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen.

button3Down                    =EButton3Down 

# Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen.

button3Up                      =EButton3Up 

# Represents a device switch off event.

switchOff                      =ESwitchOff 

# Represents a key being continually pressed event.

keyRepeat                      =EKeyRepeat

# Represents a case open event. The meaning of a case is hardware specific.

caseOpen                       =ECaseOpen

# Represents a case close event. The meaning of a case is hardware specific. 

caseClose                      =ECaseClose 

# Represents a device restart 

restartSystem                  =ERestartSystem