|
1 # This is the global environment file to configure the touch-screen test suite on a specific device |
|
2 # The current default touch screen test suite values are configured for TI OMAP 2420 (H4) hardware digitiser device |
|
3 # Licencees may need to configure below values to specific devices and also where applicable, |
|
4 # check supported HAL Enum's |
|
5 |
|
6 |
|
7 [generic] |
|
8 |
|
9 # A timeout value in microseconds. |
|
10 # This is a 10 second timeout used in the manual testcases |
|
11 minTimeout =1000000 |
|
12 |
|
13 # A timeout value in microseconds. |
|
14 # This is a 50 second timeout used in the manual testcases |
|
15 maxTimeout =5000000 |
|
16 |
|
17 # Defines the error margin in pixels that the digitiser test suite will cater for. |
|
18 errorMargin =10 |
|
19 |
|
20 |
|
21 # A hexadecimal value used to represent keycode values used in tests where manual confirmation |
|
22 # is required via a key press. |
|
23 # The keycode value represents the TKeyCode enum value, by default the hexadecimal value |
|
24 # used in this suite is the 'one' key. |
|
25 # (Please note that some of these mappings are device dependant). |
|
26 keyCode =0x0031 |
|
27 |
|
28 [confirm] |
|
29 instructions =Press the number one key to pass the test case. Any key to fail. |
|
30 |
|
31 [exitBox] |
|
32 # Defines the horizontal co-ordinate value for the positioning of the exit box. |
|
33 minX =10 |
|
34 |
|
35 # Defines the vertical co-ordinate value for the positioning of the exit box. |
|
36 minY =100 |
|
37 |
|
38 # Defines the horizontal co-ordinate value for the positioning of the exit box. |
|
39 maxX =40 |
|
40 |
|
41 # Defines the vertical co-ordinate value for the positioning of the exit box. |
|
42 maxY =120 |
|
43 |
|
44 |
|
45 [randomPixels] |
|
46 # Defaults values used in the scenario where the user has |
|
47 # to touch any pixel on the screen with a stylus, and manually confirm if a test has passed. |
|
48 instructions =Touch any number of screen pixels randomly with stylus. To exit testcase hit the exit box. |
|
49 pixelfeedback =Did the pixels hightlight correctly? Press the number one key to pass the test case. Any key to fail. |
|
50 |
|
51 # Defines the number of pixels that will need to be verified. In the default scenario we are using -1 to indicate an unlimited number of |
|
52 # pixels, for example here the use of the number 3 would indicate three pixels to verify. |
|
53 pointsTotal =-1 |
|
54 |
|
55 [randomLine] |
|
56 instructions =Draw a straight line from any point to any point. To exit testcase hit the exit box. |
|
57 pixelfeedback =Did correct pixels hightlight? Press the number one key to pass the test case. Any key to fail. |
|
58 |
|
59 # Defines the number of pixels that will need to be verified. In the default scenario we are using -1 to indicate an unlimited number of |
|
60 # pixels |
|
61 pointsTotal =3 |
|
62 |
|
63 [preDrawnDots] |
|
64 # Defaults values used in the scenario when pixels are predrawn on the screen, and the user has |
|
65 # to touch each pixel with a stylus. |
|
66 instructions =Touch the inside the drawn rectangle. To exit testcase hit the exit box |
|
67 |
|
68 # Defines the number of pixels that will be predrawn on the screen ready to verify. |
|
69 pointsTotal =3 |
|
70 |
|
71 # Define the predrawn co-ordinates here there are 3 but this can be increased by adding further values |
|
72 # i.e 4_x and so forth |
|
73 1_x =30 |
|
74 1_y =210 |
|
75 |
|
76 2_x =180 |
|
77 2_y =60 |
|
78 |
|
79 3_x =200 |
|
80 3_y =300 |
|
81 |
|
82 |
|
83 [preDrawnRect] |
|
84 # Defaults values used in the scenario when pixels are predrawn on the screen, and the user has |
|
85 # to touch each pixel with a stylus. |
|
86 |
|
87 instructions =With stylus, draw a line within this box. To exit testcase hit the exit box |
|
88 |
|
89 # Defines the number of pixels that will be predrawn on the screen ready to verify |
|
90 eventTotal =3 |
|
91 |
|
92 # Default values used in the scenario where a line is predrawn on the screen, and the user has |
|
93 # to follow the line with a stylus. the values below indicate the defualt Top left and bottom right of that rect |
|
94 tl_x =80 |
|
95 tl_y =180 |
|
96 |
|
97 br_x =200 |
|
98 br_y =200 |
|
99 |
|
100 [colour] |
|
101 # The mask value of the colour black |
|
102 black =0x00 |
|
103 # The mask value of the colour white |
|
104 white =0xFF |
|
105 |
|
106 [displayMode] |
|
107 # Define the mode display mode for the screen to use in these tests |
|
108 value ={displayMode,defaultmode} |
|
109 expected ={displayMode,defaultmode} |
|
110 |
|
111 # Define the default mode display mode for the screen |
|
112 defaultmode ={displayMode,mode3} |
|
113 |
|
114 # Define display mode for the screen |
|
115 mode0 =0 |
|
116 |
|
117 # Define display mode for the screen |
|
118 mode1 =1 |
|
119 |
|
120 # Define display mode for the screen |
|
121 mode2 =2 |
|
122 |
|
123 # Define display mode for the screen |
|
124 mode3 =7 |
|
125 |
|
126 # Define display mode for the screen |
|
127 mode4 =4 |
|
128 |
|
129 [haldata] |
|
130 |
|
131 # Default value of the the pen/digitizer horizontal resolution, in pixels |
|
132 ePenXValue =365 |
|
133 |
|
134 # Default value of the pen/digitizer vertical resolution, in pixels. |
|
135 ePenYValue =280 |
|
136 |
|
137 [halDataOff] |
|
138 # Default value of the the HAL Data to set or get. |
|
139 value =0 |
|
140 expected =0 |
|
141 |
|
142 [halDataOn] |
|
143 # Default value of the the HAL Data to set or get |
|
144 value =1 |
|
145 expected =1 |
|
146 |
|
147 [rawEvent] |
|
148 # Defines the Enum strings used by TRawEvent. |
|
149 |
|
150 # Represents an uninitialised event object. |
|
151 none =ENone |
|
152 |
|
153 # EPointerMove A pointer device (e.g. a pen) has moved. Only changes in Cartesian coordinates are tracked. |
|
154 pointerMove =EPointerMove |
|
155 |
|
156 # A switch on event caused by a screen tap using a pointer device. |
|
157 pointerSwitchOn =EPointerSwitchOn |
|
158 |
|
159 # Represents a keyboard key down event. |
|
160 keyDown =EKeyDown |
|
161 |
|
162 #Represents a keyboard key up event. |
|
163 keyUp =EKeyUp |
|
164 |
|
165 # Represents a redraw event. |
|
166 redraw =ERedraw |
|
167 |
|
168 # Represents a device switch on event. |
|
169 switchOn =ESwitchOn |
|
170 |
|
171 active =EActive |
|
172 |
|
173 inactive =EInactive |
|
174 |
|
175 # Represents a modifier key being pressed. |
|
176 updateModifiers =EUpdateModifiers |
|
177 |
|
178 # Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen |
|
179 button1Down =EButton1Down |
|
180 |
|
181 # Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen. |
|
182 button1Up =EButton1Up |
|
183 |
|
184 # Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen. |
|
185 button2Down =EButton2Down |
|
186 |
|
187 # Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen. |
|
188 button2Up =EButton2Up |
|
189 |
|
190 # Represents a button down event. This is typically used to represent a pointing device coming into contact with a touch sensitive screen. |
|
191 button3Down =EButton3Down |
|
192 |
|
193 # Represents a button up event. This is typically used to represent a pointing device being lifted away from a touch sensitive screen. |
|
194 button3Up =EButton3Up |
|
195 |
|
196 # Represents a device switch off event. |
|
197 switchOff =ESwitchOff |
|
198 |
|
199 # Represents a key being continually pressed event. |
|
200 keyRepeat =EKeyRepeat |
|
201 |
|
202 # Represents a case open event. The meaning of a case is hardware specific. |
|
203 caseOpen =ECaseOpen |
|
204 |
|
205 # Represents a case close event. The meaning of a case is hardware specific. |
|
206 caseClose =ECaseClose |
|
207 |
|
208 # Represents a device restart |
|
209 restartSystem =ERestartSystem |
|
210 |