Destructor. Closes the audio clip and frees resources.

Adds a meta data entry to the audio clip.

Returns the controller implementation information associated with the playback controller

Returns the controller implementation information associated with the recording controller.

Cancels the registered notification event.

Removes any window defined on the audio sample data.

All subsequent playing, position setting and position querying requests are mapped to the whole of the audio sample data.

Close the current audio clip.

Deletes all audio sample data from the beginning of the audio clip to the current position. The effects of the function cannot be undone.

The function is synchronous and can leave if there is a problem. The leave code depends on the configuration.

Deletes all audio sample data after the current head position. The effects of the function cannot be undone.

The function is synchronous and can leave if there is a problem. The leave code depends on the configuration.

Returns the bit rate in bits per second that the data sink is currently set to.

Returns the codec that is currently set for the destination audio clip.

Returns the format(UID) of the destination audio clip.

Returns the number of channels that the destination audio clip is currently configured to support.

Returns the sample rate in samples/second that the destination data sink is currently set to.

Returns the duration of the audio clip.

Returns the duration of the audio sample in microseconds, and the duration state.

The function raises a CMdaAudioPlayerUtility 1 panic if the audio player utility is not initialised.

Returns the current progress of audio loading.

Gets a controller's DRM custom command implementation.

Returns the current gain setting of the audio device.

Returns the specified meta data entry from the current audio clip.

Returns the number of meta data entries associated with this clip.

Returns The current balance setting for the audio device. This function may not return the same value as passed to SetPlaybackBalance depending on the internal implementation in the underlying components.

Returns the current recording balance setting between the left and right stereo microphones.

Returns a list of the supported bit rates for recording to the data sink.

Returns a list of the supported codecs for the conversion destination.

Returns a list of the supported number of channels for recording. For example 1 for mono, 2 for stereo and so on.

If a destination sample rate has not been set then GetSupportedSampleRatesL() returns all valid sample rates

If a destination sample rate has been set then GetSupportedSampleRatesL() returns all valid sample rates less than or equal to the destination sample rate

Returns the current volume setting for the audio device.

Return the maximum value for the gain

Returns the maximum volume setting for the audio device.

Constructs and initialises a new instance of the audio recorder for playing, recording and editing audio sample data.

The function leaves if the audio recorder object cannot be created.

Opens a descriptor to play back or record audio sample data (const version).

Opens a descriptor to play back or record audio sample data.

Opens an audio clip from a descriptor to play back existing audio data from or to record new audio data to.

Opens a file to play back or record audio sample data.

Opens a file to play back or record audio sample data.

Opens a file to play or record audio sample data.

Opens an audio clip from a file to play back existing audio data or to record new audio data.

Opens an audio clip from a file to play back existing audio data or to record new audio data.

Opens an audio clip from a filename or an open file handle to play back existing audio data or to record new audio data.

Opens a TMdaClipLocation package of audio data that can be played back or recorded to.

Opens an audio clip from a URL to play back existing audio data from or to record new audio data to.

Opens an audio clip from a URL to play back or record audio sample data.

Send a asynchronous custom command to the recording controller.

Send a asynchronous custom command to the recording controller.

Note: This method will return immediately. The RunL of the active object owning the aStatus parameter will be called when the command is completed by the controller framework.

Send a synchronous custom command to the playback controller

Send a synchronous custom command to the playback controller.

Begins playback of audio sample data at the current playback position using the current volume, gain and priority settings.

Returns the current head position.

The head position is defined in terms of a time interval measured from the beginning of the audio sample data.

Send a asynchronous custom command to the recording controller.

Note: This method will return immediately. The RunL of the active object owning the aStatus parameter will be called when the command is completed by the controller framework.

Send a asynchronous custom command to the recording controller

Note: This method will return immediately. The RunL of the active object owning the aStatus parameter will be called when the command is completed by the controller framework.

Sends a synchronous custom command to the recording controller.

Sends a synchronous custom command to the recording controller.

Starts appending new audio sample data.

The new audio sample data is appended to the existing audio sample data in the same format as the existing audio sample data. If existing data is to be overwritten, then it should be cropped to the appropriate length before appending the new data.

Note: Before starting to record, make sure that the gain is set by calling SetGain(), as the initial gain is undefined. The gain might also have been modified by another client application.

Returns the recording time available for the selected file or descriptor and encoding format.

Registers the Event for Notification when resource is avaliable.

Register to receive notifications of audio loading/rebuffering

Removes a specified meta data entry from the audio clip.

Replaces the specified meta data entry with a new entry.

Sets the audio device mode. This function is provided for binary compatibility, but does not have any effect from 7.0s.

Sets the bit rate of the data sink in bits per second.

The bit rate must be one of the supported bit rates of the data sink. Use GetSupportedBitRatesL() to retrieve a list of supported bit rates for the data sink.

Sets the codec to use with the record controller.

Sets the format of the audio clip. This can only be done if the audio clip does not exist.

Sets the number of channels for the recorded audio clip.

The number of channels must be one of the values returned by GetSupportedNumberOfChannelsL().

Sets the sample rate for the conversion destination data sink.

The sample rate must be one of the supported sample rates of the data sink. Use GetSupportedSampleRatesL() to retrieve a list of supported sample rates for the data sink. This function should not be used if the audio clip already exists; that is, in the "Open and Append" scenario, when the function's behaviour is undefined.

Sets the gain for the audio device to a specified value.

Sets the maximum size for a file that is being recorded.

When this limit is reached, MMF stops recording and notifies the client application. Notification is caused by MMdaObjectStateChangeObserver::MoscoStateChangeEvent() with the error code KErrEof.

This function is provided so that applications such as recorders can limit the amount of file storage/memory that should be allocated.

Defines a window on the audio sample data.

The window is defined in terms of a start and end position. When the current playback position reaches the window end position, or Stop() is called, the current playback position is set to the window start position and playback stops.

The current playback position is not affected by a call to SetPlayWindow() unless it is outside the new playback window, in which case it is set to the window start or end position depending on which one is closer.

The window persists until ClearPlayWindow() is called. Loading new audio sample data without adjusting or clearing the window will result in playback errors if the window is outside the new data.

Sets the current playback balance.

The balance can be any value between KMMFBalanceMaxLeft and KMMFBalanceMaxRight, the default value being KMMFBalanceCenter.

Sets the head position.

Sets the recording priority.

The priority is used to arbitrate between multiple objects simultaneously trying to access the sound hardware.

Sets the current recording balance setting between the left and right stereo microphones

The microphone balance can be changed before or during recording and is effective immediately.

Sets the number of times the audio sample is to be repeated during the PlayL() operation.

A period of silence can follow each playing of the audio sample. The audio sample can be repeated indefinitely or until stopped.

Set the priority of the playback controller's sub thread.

This can be used to increase the responsiveness of the audio plugin to minimise any lag in processing. This function should be used with care as it may have knock-on effects elsewhere in the system.

Set the priority of the record controller's sub thread.

This can be used to increase the responsiveness of the audio plugin to minimise any lag in processing. This function should be used with care as it may have knock-on effects elsewhere in the system.

Sets the playback volume for the audio device to a specified value.

Sets the volume increase gradient.

This defines the period over which the volume level of a played audio sample is to rise smoothly from nothing to the normal volume level.

Returns the bit rate of the audio clip.

Returns the current state of the audio sample data.

Stops the current operation (playback/recording/conversion).

The operation is stopped at the current location. For a playback operation, the head is positioned at the last played data.

Ensures that any subsequent calls to OpenXYZ() will create controllers that share a heap.

The default behaviour is that for each recorder utility a controller with its own heap is created. Each heap uses a chunk, so using this function avoids situations where the number of chunks per process is limited. The default behaviour is generally to be preferred, and should give lower overall memory usage. However, if many controllers are to be created for a particular thread, then this function should be used to prevent running out of heaps or chunks.

Waits for the client to resume the play even after the default timer expires.